refs #17038

filter out the bridge when mac checking

asterisk-1.8.x-mod/Makefile

@@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk
 PKG_NAME:=asterisk18-mod
 PKG_VERSION:=1.8.10.1
 
-PKG_SOURCE_VERSION:=ee99af0d91a2197529b13075d802ebc37e644e40
+PKG_SOURCE_VERSION:=d780c4c7a34019b6c673d36338dca9cfb34f3e46
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_URL:=http://public.inteno.se:/asterisk-1.8.x
 
@@ -41,7 +41,7 @@ define Package/asterisk18-mod
 $(call Package/asterisk18-mod/Default)
   TITLE:=Complete open source PBX, v1.8x
   MENU:=1
-  DEPENDS:= +natalie-dect-h +PACKAGE_bcmkernel:bcmkernel +PACKAGE_bcmopen:bcmopen +libopenssl +libncurses +libpopt +libpthread +uci +ubus +zlib @!TARGET_avr32
+  DEPENDS:= +natalie-dect-h +PACKAGE_bcmkernel:bcmkernel +PACKAGE_bcmopen:bcmopen +libopenssl +libstdcpp +libncurses +libpopt +libpthread +uci +ubus +zlib @!TARGET_avr32
 endef
 
 define Package/asterisk18-mod/description
@@ -451,6 +451,7 @@ define Package/asterisk18-mod/install
 	done
 	$(INSTALL_DIR) $(1)/usr/sbin
 	$(INSTALL_BIN) $(PKG_INSTALL_DIR)/usr/sbin/asterisk $(1)/usr/sbin/
+	$(INSTALL_BIN) $(PKG_INSTALL_DIR)/usr/sbin/astcanary $(1)/usr/sbin/
 	$(INSTALL_DIR) $(1)/etc/default
 	$(INSTALL_DATA)  ./files/asterisk.default $(1)/etc/default/asterisk
 	$(INSTALL_DIR) $(1)/etc/init.d

asterisk-1.8.x-mod/files/asterisk.hotplug

@@ -5,15 +5,15 @@
 config_load voice_client
 config_get bindintf SIP bindintf
 
-[ "$INTERFACE" == "$bindintf" ] || exit 0
+[ "$INTERFACE" == "$bindintf" -o -z "$bindintf" ] || exit 0
 
 . /lib/functions/network.sh
 
 if [ -n "$bindintf" ]; then
 	network_get_ipaddr bindaddr "$bindintf"
 	[ -z "$bindaddr" ] && network_get_ipaddr6 bindaddr "$bindintf"
-	bindaddr="${bindaddr:-0.0.0.0}"
-	sed -i "s/bindaddr=.*/bindaddr=$bindaddr/g" /etc/asterisk/sip.conf
-	[ -e /var/run/asterisk/asterisk.ctl ] && /etc/init.d/asterisk reload
 fi
 
+bindaddr="${bindaddr:-0.0.0.0}"
+sed -i "s/bindaddr=.*/bindaddr=$bindaddr/g" /etc/asterisk/sip.conf
+[ -e /var/run/asterisk/asterisk.ctl ] && /etc/init.d/asterisk reload

asterisk-1.8.x-mod/files/asterisk.init

@@ -32,7 +32,7 @@ start_service() {
 	init_asterisk
 
 	procd_open_instance
-	procd_set_param command "$PROG" -f
+	procd_set_param command /usr/bin/taskset 2 "$PROG" -f -p -q
 	procd_set_param respawn
 	procd_close_instance
 #	service_start /usr/sbin/asterisk

ated/Makefile

@@ -14,7 +14,7 @@ PKG_RELEASE:=1
 
 PKG_SOURCE_VERSION:=f614cba983d827d5185c60a6a5a35530621d44d2
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_URL:=http://public.inteno.se:/ated
+PKG_SOURCE_URL:=https://dev.iopsys.eu/mediatek/ated.git
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_RELEASE)-$(PKG_SOURCE_VERSION).tar.gz
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)

brcmslic/Makefile

@@ -0,0 +1,47 @@
+#
+# Copyright (C) 2006-2010 OpenWrt.org
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+PKG_RELEASE:=1
+PKG_VERSION:=0.1
+PKG_SOURCE_URL:=git@private.inteno.se:brcmslic
+PKG_SOURCE_PROTO:=git
+PKG_SOURCE_VERSION:=837ec19e37650e424e77c921672a0806e198ba7b
+PKG_NAME:=brcmslic
+
+
+RSTRIP:=true
+export BUILD_DIR
+
+PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
+
+PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz
+
+include $(INCLUDE_DIR)/package.mk
+
+define Package/brcmslic
+  CATEGORY:=Utilities
+  TITLE:=Brcmslic
+  URL:=
+  DEPENDS:=
+endef
+
+define Package/brcmslic/description
+	Brcmslic
+endef
+
+
+define Package/brcmslic/install
+	$(INSTALL_DIR) $(1)/usr/sbin
+	$(INSTALL_DIR) $(1)/etc/init.d/
+
+	$(INSTALL_BIN) $(PKG_BUILD_DIR)/src/brcmslic $(1)/usr/sbin/
+	$(INSTALL_BIN) $(PKG_BUILD_DIR)/src/endpt $(1)/usr/sbin/
+endef
+
+$(eval $(call BuildPackage,brcmslic))

brcmslic/files/dect.config

@@ -0,0 +1,4 @@
+
+config dect 'dect'
+	option radio 'auto'
+

dectmngr2/Makefile

@@ -9,9 +9,9 @@ include $(TOPDIR)/rules.mk
 
 PKG_RELEASE:=1
 PKG_VERSION:=1.1.0
-PKG_SOURCE_URL:=http://public.inteno.se:/dectmngr2
+PKG_SOURCE_URL:=https://dev.iopsys.eu/iopsys/dectmngr.git
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_VERSION:=13da1568d57b8e6732dadc16de828d64c81906b8
+PKG_SOURCE_VERSION:=930b8908a0159cfdef9d5c8861791db176dad7f5
 PKG_NAME:=dectmngr2
 
 

endptcfg/Makefile

@@ -8,7 +8,7 @@
 include $(TOPDIR)/rules.mk
 
 PKG_NAME:=endptcfg
-PKG_VERSION:=0.2
+PKG_VERSION:=0.3
 
 PKG_SOURCE_VERSION:=1194b05278bd0945ca5c76436e56617b86871a65
 ifeq ($(CONFIG_ENDPT_OPEN),y)

fping/Makefile

@@ -0,0 +1,54 @@
+#
+# Copyright (C) 2016 Nikil Mehta <nikil.mehta@gmail.com>
+#
+# This is free software, licensed under the GNU General Public License v2.
+# See /LICENSE for more information.
+#
+
+include $(TOPDIR)/rules.mk
+
+PKG_NAME:=fping
+PKG_VERSION:=4.0
+PKG_RELEASE:=2
+
+PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.gz
+PKG_SOURCE_URL:=http://fping.org/dist/
+PKG_HASH:=67eb4152b98ad34f99d2eec4e1098a0bb52caf13c0c89cd147349d08190fe8ce
+
+PKG_MAINTAINER:=Nikil Mehta <nikil.mehta@gmail.com>
+PKG_LICENSE:=BSD-4-Clause
+PKG_LICENSE_FILES:=COPYING
+
+PKG_INSTALL:=1
+
+include $(INCLUDE_DIR)/package.mk
+
+define Package/fping
+  SECTION:=net
+  CATEGORY:=Network
+  TITLE:=sends ICMP ECHO_REQUEST packets to network hosts
+  URL:=http://fping.org/
+endef
+
+
+define Package/fping/description
+	fping is a ping like program which uses the Internet Control Message Protocol
+	(ICMP) echo request to determine if a target host is responding.  fping
+	differs from ping in that you can specify any number of targets on the command
+	line, or specify a file containing the lists of targets to ping.  Instead of
+	sending to one target until it times out or replies, fping will send out a
+	ping packet and move on to the next target in a round-robin fashion.
+endef
+
+CONFIGURE_ARGS+= \
+	--enable-ipv4 \
+	--enable-ipv6
+
+TARGET_CFLAGS += -std=gnu99
+
+define Package/fping/install
+	$(INSTALL_DIR) $(1)/usr/bin
+	$(INSTALL_BIN) $(PKG_INSTALL_DIR)/usr/sbin/fping $(1)/usr/bin/
+endef
+
+$(eval $(call BuildPackage,fping))

gigaset-elements/Makefile

@@ -5,7 +5,7 @@ PKG_NAME:=gigaset-elements
 PKG_VERSION:=2.4.2
 # PKG_RELEASE=$(PKG_SOURCE_VERSION)
 
-PKG_GIGASET_ELEMENTS_SRC_URL ?= git@public.inteno.se:gigaset-elements.git
+PKG_GIGASET_ELEMENTS_SRC_URL ?= git@dev.iopsys.eu:3rdparty/gigaset-elements.git
 PKG_GIGASET_ELEMENTS_VERSION ?= v$(PKG_VERSION)
 
 PKG_SOURCE_URL:=$(PKG_GIGASET_ELEMENTS_SRC_URL)

ice-client/Makefile

@@ -19,14 +19,14 @@ export PLATFORM_INCLUDE:=platforms/iopsys/build.mk
 
 export DATE:=$(shell date +%Y-%m-%d-%H-%M-%S)
 export LOGIN:=$(shell whoami)
-BASE_PKG_VERSION:=4.4.0
-PKG_RELEASE:=RC4
-PKG_VERSION:=$(BASE_PKG_VERSION)-$(PKG_RELEASE)_$(DATE)_$(LOGIN)
+BASE_PKG_VERSION:=5.3.8
+PKG_RELEASE:=
+PKG_VERSION:=$(BASE_PKG_VERSION)-$(PKG_RELEASE)-$(DATE)_$(LOGIN)
 export PKG_VERSION
 
 ###########################--RELEASE--################################
 
-PKG_SOURCE_VERSION:=e855fdb65ec312e9ec044ce9319d6ac17fde57cd
+PKG_SOURCE_VERSION:=5cc855907b9d6a13d36fd619b579fcf3c6f24b5c
 ifeq ($(CONFIG_ICE_OPEN),y)
 TARGET_PROFILE=$(shell echo $(CONFIG_TARGET_BOARD) | sed s/\"//g)
 PKG_SOURCE_URL:=http://iopsys.inteno.se/iopsys/consumer/
@@ -154,6 +154,7 @@ define Package/ice-client/install
 	$(CP) $(PKG_BUILD_DIR)/scripts/etc/config/ice $(1)/etc/config
 	$(INSTALL_DIR) $(1)/etc/iopsys
 	$(CP) $(PKG_BUILD_DIR)/scripts/server.ini $(1)/etc/iopsys	
+	$(CP) $(PKG_BUILD_DIR)/scripts/defaults.ini $(1)/etc/iopsys	
 	$(CP) $(PKG_BUILD_DIR)/scripts/modify.ini $(1)/etc/iopsys
 	$(INSTALL_DIR) $(1)/etc/iopsys/certificates
 	$(CP) $(PKG_BUILD_DIR)/scripts/cert_server_ca.pem $(1)/etc/iopsys/certificates

ice-client/files/ice-client.uci_default

@@ -1,13 +1,15 @@
 #!/bin/sh
 
 grep -rq "^ice:" /etc/passwd || {
-	local password="$(db get hw.board.wpaKey)"
-	if [ -n "$password" ]; then
-		adduser -D -H -s /bin/false ice
-		(echo $password; sleep 1; echo $password) | passwd ice >/dev/null 2>&1
-	fi
+	adduser -D -H -s /bin/false ice
 }
 
+uci -q delete passwords.ice
+uci -q set passwords.ice=usertype
+uci -q set passwords.ice.password="\$WPAKEY"
+uci -q add_list passwords.ice._access_r=root
+uci -q commit passwords
+
 uci show rpcd | grep username=.*ice.* >/dev/null || {
 cat >> /etc/config/rpcd << EOF
 
@@ -47,6 +49,7 @@ config login
 	list write 'juci-network-netifd'
 	list write 'juci-owsd'
 	list write 'juci-printer'
+	list write 'juci-realtime-graphs'
 	list write 'juci-samba'
 	list write 'juci-sfp'
 	list write 'juci-snmpd'
@@ -56,6 +59,7 @@ config login
 	list write 'juci-usb'
 	list write 'core'
 	list write 'unauthenticated'
+
 EOF
 }
 

icwmp/Makefile

@@ -8,11 +8,11 @@
 include $(TOPDIR)/rules.mk
 
 PKG_NAME:=icwmp
-PKG_VERSION:=3.0-2017-06-01
+PKG_VERSION:=3.0-2018-03-01
 PKG_FIXUP:=autoreconf
-PKG_SOURCE_URL:=http://public.inteno.se:/icwmp.git
+PKG_SOURCE_URL:=https://dev.iopsys.eu/iopsys/icwmp.git
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_VERSION:=cff928dae59aa115a6f74f68ee4f08dfda2beeb7
+PKG_SOURCE_VERSION:=af5476c35d03c03f82c22a65cba932f6df096808
 PKG_RELEASE=$(PKG_SOURCE_VERSION)
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
@@ -66,6 +66,10 @@ define Build/Prepare
 endef
 endif
 
+ifeq ($(CONFIG_TARGET_IBOARDID),"EX400")
+TARGET_CFLAGS += -DEX400
+endif
+
 TARGET_CFLAGS += \
 	-D_GNU_SOURCE -D_AADJ
 
@@ -129,9 +133,11 @@ define Package/icwmp-$(BUILD_VARIANT)/install
 	$(INSTALL_CONF) $(PKG_BUILD_DIR)/config/cwmp $(1)/etc/config
 	$(INSTALL_CONF) $(PKG_BUILD_DIR)/config/firewall.cwmp $(1)/etc/firewall.cwmp
 	$(INSTALL_DIR) $(1)/etc/init.d
-	$(INSTALL_DIR) $(1)/etc/uci-defaults
 	$(INSTALL_BIN) $(PKG_BUILD_DIR)/init/icwmpd.init $(1)/etc/init.d/icwmpd
+	$(INSTALL_DIR) $(1)/etc/uci-defaults
 	$(INSTALL_BIN) $(PKG_BUILD_DIR)/uci-defaults/90-cwmpfirewall $(1)/etc/uci-defaults/90-cwmpfirewall
+	$(INSTALL_DIR) $(1)/etc/hotplug.d/iface
+	$(CP) ./files/icwmp.hotplug $(1)/etc/hotplug.d/iface/90-icwmp
 ifeq ($(CONFIG_CWMP_SCRIPTS_FULL),y)
 	$(INSTALL_DIR) $(1)/usr/share/icwmp
 	$(CP) $(PKG_BUILD_DIR)/scripts/defaults $(1)/usr/share/icwmp

icwmp/files/icwmp.hotplug

@@ -0,0 +1,76 @@
+#!/bin/sh
+
+. /lib/functions/network.sh
+
+[ "$ACTION" == "ifup" ] || exit 0
+
+[ -f /etc/config/cwmp ] || exit 0
+
+handle_icwmp_restart() {
+	[ -f /tmp/switching_mode ] && exit 0
+
+	[ "$INTERFACE" == "loopback" ] && exit 0
+
+	local defwan=$(uci -q get cwmp.cpe.default_wan_interface)
+	[ -n "$defwan" -a "$(uci -q get network.$defwan)" == "interface" -a "$defwan" != "$INTERFACE" ] && exit 0
+
+	local islan="$(uci -q get network.$INTERFACE.is_lan)"
+	[ "$islan" == "1" ] && exit 0
+
+	local proto="$(uci -q get network.$INTERFACE.proto)"
+	[ "$proto" == "none" ] && exit 0
+
+	local ifname="$(uci -q get network.$INTERFACE.ifname)"
+	[ "${ifname:0:1}" == "@" ] && exit 0
+
+	mkdir -p /tmp/ipv4
+
+	network_flush_cache
+
+	local previpaddr=""
+	local curipaddr=""
+	local ipaddrfile=/tmp/ipv4/$INTERFACE-ipaddr
+	previpaddr=$(cat $ipaddrfile 2>/dev/null)
+	network_get_ipaddr curipaddr $INTERFACE
+	[ -n "$curipaddr" ] && echo $curipaddr > $ipaddrfile || rm -f $ipaddrfile
+
+	local prevgateway=""
+	local curgateway=""
+	local gatewayfile=/tmp/ipv4/$INTERFACE-gateway
+	prevgateway=$(cat $gatewayfile 2>/dev/null)
+	network_get_gateway curgateway $INTERFACE
+	[ -n "$curgateway" ] && echo $curgateway > $gatewayfile || rm -f $gatewayfile
+
+	local prevsubnets=""
+	local cursubnets=""
+	local subnetsfile=/tmp/ipv4/$INTERFACE-subnets
+	prevsubnets=$(cat $subnetsfile 2>/dev/null)
+	network_get_subnets cursubnets $INTERFACE
+	[ -n "$cursubnets" ] && echo $cursubnets > $subnetsfile || rm -f $subnetsfile
+
+	local prevdnsservers=""
+	local curdnsservers=""
+	local dnsserverfile=/tmp/ipv4/$INTERFACE-dnsservers
+	prevdnsservers=$(cat $dnsserverfile 2>/dev/null)
+	network_get_dnsserver curdnsservers $INTERFACE
+	[ -n "$curdnsservers" ] && echo $curdnsservers > $dnsserverfile || rm -f $dnsserverfile
+
+	local prevdev=""
+	local curdev=""
+	local devfile=/tmp/ipv4/$INTERFACE-dev
+	prevdev=$(cat $devfile 2>/dev/null)
+	network_get_device curdev $INTERFACE
+	[ -n "$curdev" ] && echo $curdev > $devfile || rm -f $devfile
+
+	[ \
+		"$prevdev" == "$curdev" -a \
+		"$previpaddr" = "$curipaddr" -a \
+		"$prevgateway" = "$curgateway" -a \
+		"$prevsubnets" = "$cursubnets" -a \
+		"$prevdnsservers" = "$curdnsservers" \
+	] && exit 0
+
+	/etc/init.d/icwmpd reload &
+}
+
+handle_icwmp_restart

inbd/Makefile

@@ -12,9 +12,9 @@ PKG_NAME:=inbd
 PKG_VERSION:=1.0.0
 PKG_RELEASE:=1
 
-PKG_SOURCE_VERSION:=2d474e9ff37b9cfcffd4b9ac8eba8db03eb38a21
+PKG_SOURCE_VERSION:=92f918d26c0ffc22d1704f5ea6cbb0bd7fdbdab9
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_URL:=http://public.inteno.se/inbd
+PKG_SOURCE_URL:=https://dev.iopsys.eu/iopsys/inbd
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_RELEASE)-$(PKG_SOURCE_VERSION).tar.gz
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)

inteno-netmodes/Makefile

@@ -12,6 +12,7 @@ include $(INCLUDE_DIR)/package.mk
 
 define Package/inteno-netmodes
   CATEGORY:=Base system
+  DEPENDS:=+fping
   TITLE:=Predefined Network Modes
 endef
 

inteno-netmodes/files/etc/hotplug.d/iface/01-netmode-firewall-handler

@@ -1,53 +0,0 @@
-#!/bin/sh
-
-[ "$INTERFACE" != "wan" ] && exit
-
-. /lib/functions/network.sh
-
-network_get_ipaddr ip $INTERFACE
-
-[ -z "$ip" ] && exit
-
-toggle_firewall() {
-	local section=$1
-	local disable=$2
-	config_get name "$1" name
-	if [ "$name" == "wan" ]; then
-		uci -q set firewall.settings.disabled=$disable
-		if [ "$disable" == "1" ]; then
-			uci -q set firewall.$section.input="ACCEPT"
-		else
-			uci -q set firewall.$section.input="REJECT"
-		fi
-		uci -q commit firewall
-	fi
-}
-
-set_disabled() {
-	config_load firewall
-	config_foreach toggle_firewall zone $1
-}
-
-test_ip() {
-	if [ -n "$(echo $ip | grep -E '^(192\.168|10\.|172\.1[6789]\.|172\.2[0-9]\.|172\.3[01]\.)')" ]; then
-		# private IP
-		set_disabled 1
-	else
-		# public IP
-		set_disabled 0
-		[ "$1" -eq "1" ] && {
-			uci set netmode.setup.repeaterready=0
-			uci commit netmode
-			local pid="$(ps | grep wificontro[l] | awk '/repeater/ {print $1}')"
-			[ "$pid" != "" ] && kill -9 $pid
-			pid="$(pidof netmode-client-detect)"
-			[ "$pid" == "" ] && /sbin/netmode-client-detect &
-		}
-	fi
-}
-
-case "$(uci -q get netmode.setup.curmode)" in
-                repeater*) test_ip ;;
-		*) [ "$(uci -q get netmode.setup.repeaterready)" == "1" ] && test_ip 1;;
-esac
-

inteno-netmodes/files/etc/hotplug.d/iface/01-netmode-handler

@@ -0,0 +1,119 @@
+#!/bin/sh
+
+[ "$INTERFACE" != "wan" ] && exit
+
+. /lib/functions/network.sh
+
+network_get_ipaddr ip $INTERFACE
+repeaterready="$(uci -q get netmode.setup.repeaterready)"
+
+[ -z "$ip" ] && exit
+
+toggle_firewall() {
+	local section=$1
+	local disable=$2
+	config_get name "$1" name
+	if [ "$name" == "wan" ]; then
+		uci -q set firewall.settings.disabled=$disable
+		if [ "$disable" == "1" ]; then
+			uci -q set firewall.$section.input="ACCEPT"
+		else
+			uci -q set firewall.$section.input="REJECT"
+		fi
+		uci -q commit firewall
+	fi
+}
+
+set_disabled() {
+	config_load firewall
+	config_foreach toggle_firewall zone $1
+	/etc/init.d/firewall reload
+}
+
+is_inteno_macaddr()
+{
+	macaddr=$1
+
+	echo $macaddr | grep -i -e "^00:22:07" \
+				-e "^02:22:07" \
+				-e "^44:D4:37" \
+				-e "^00:0C:07" \
+				-e "^02:0C:07" \
+				-e "^06:0C:07" \
+				-e "^00:0C:43" \
+				-e "^02:0C:43" \
+				-e "^06:0C:43" \
+	&& return
+	false
+}
+
+switch_mode() {
+	[ "$repeaterready" == "1" ] || return
+
+	# flush the ip on br-lan; br-lan will anyhow be deleted.
+	# this is needed if the ip received on the wan is also from the same net
+	ip addr flush dev br-lan
+
+	# flush iptables in case the MASTER
+	# tries to configure us before
+	# firewall is disabled the proper way
+	iptables -F
+
+	ubus call leds set  '{"state" : "allflash"}'
+
+	local ret=0
+	# let netmode-conf up to 20 seconds before switching mode
+	for tm in 2 4 6 8; do
+		if [ -f /tmp/wificontrol.txt ]; then
+			ret=1
+			break
+		fi
+		sleep $tm
+	done
+
+	# let netmode-conf take over
+	[ $ret -eq 1 ] && return
+
+	# go head with switching mode
+	touch -f /tmp/switching_mode
+	echo "Switching to 'extender' mode" > /dev/console
+	uci -q set netmode.setup.curmode='repeater'
+	uci set netmode.setup.repeaterready=0
+	uci commit netmode
+	/etc/init.d/netmode reload
+	echo "Restarting network services" > /dev/console
+	ubus call network reload
+	wifi reload nodat
+	ubus call router.network reload
+	ubus call leds set  '{"state" : "normal"}'
+	rm -f /tmp/switching_mode
+}
+
+test_ip() {
+	if [ -n "$(echo $ip | grep -E '^(192\.168|10\.|172\.1[6789]\.|172\.2[0-9]\.|172\.3[01]\.)')" ]; then
+		# private IP
+		switch_mode
+		set_disabled 1
+	else
+		# public IP
+		set_disabled 0
+		[ "$1" -eq "1" ] && {
+			uci set netmode.setup.repeaterready=0
+			uci commit netmode
+			local pid="$(ps | grep wificontro[l] | awk '/repeater/ {print $1}')"
+			[ "$pid" != "" ] && kill -9 $pid
+			pid="$(pidof netmode-client-detect)"
+			[ "$pid" == "" ] && /sbin/netmode-client-detect &
+
+			# set default JUCI page to overview
+			uci -q set juci.juci.homepage="overview"
+			uci commit juci
+		}
+	fi
+}
+
+case "$(uci -q get netmode.setup.curmode)" in
+		repeater*) test_ip ;;
+		*) [ "$repeaterready" == "1" ] && test_ip 1;;
+esac
+

inteno-netmodes/files/etc/hotplug.d/iface/100-lan-follow-wan

@@ -0,0 +1,54 @@
+#!/bin/sh
+
+. /lib/functions.sh
+. /lib/functions/network.sh
+
+follow_wan='0'
+config_load dhcp
+config_get follow_wan 'lan' dhcpv6_follow_wan 0
+
+test $follow_wan = '1' || exit 0
+
+PROTO=""
+
+get_dhcp_version_of_interface() {
+	config_get PROTO $INTERFACE proto
+
+	if [ -n "$PROTO" ]; then
+		return
+	fi
+}
+
+config_load network
+config_foreach get_dhcp_version_of_interface interface
+
+lan_v6_on() {
+	logger -t lan-follow-wan "turning ON IPv6 on LAN"
+	uci set dhcp.lan.dhcpv6='server'
+}
+
+lan_v6_off() {
+	logger -t lan-follow-wan "turning OFF IPv6 on LAN"
+	uci set dhcp.lan.dhcpv6='disabled'
+}
+
+case "$ACTION" in
+	ifup)
+		if [ "$PROTO" = "dhcpv6" ]; then
+			network_flush_cache
+			network_get_ipaddr6 current_ipv6_address $INTERFACE
+
+			if [ -n "$current_ipv6_address" ]; then
+				lan_v6_on
+			else
+				lan_v6_off
+			fi
+		elif [ "$PROTO" = "dhcp" ]; then
+			lan_v6_off
+		fi
+
+		uci commit
+		/etc/init.d/odhcpd restart
+
+		;;
+esac

inteno-netmodes/files/etc/hotplug.d/iface/70-shiftrange

@@ -0,0 +1,251 @@
+#!/bin/sh
+# this scripts shifts the lan network prefixes
+# if a wan interface has the same network prefix.
+
+. /lib/functions.sh
+. /lib/functions/network.sh
+
+local lockfile="/tmp/70-shiftrange.lock"
+local restricted_nets=""
+local all_nets=""
+
+
+#####
+##### initial functions
+#####
+
+initial_check()
+{
+	# run only on ifup
+	[ "$ACTION" == "ifup" ] || exit 0
+
+	# run only for uplink (not is_lan) interfaces
+	local islan="$(uci -q get network.$INTERFACE.is_lan)"
+	[ "$islan" != "1" ] || exit 0
+
+	# run only if the uplink interface has a configured protocol
+	local proto="$(uci -q get network.$INTERFACE.proto)"
+	[ "$proto" != "none" ] || exit 0
+}
+
+finish()
+{
+    lock -u $lockfile
+    rm -f $lockfile
+}
+
+# just one instance of this script at a time
+just_one_instance()
+{
+	local counter=0
+	local limit=10
+
+	#wait for the lock to become free
+	while [ -e $lockfile ] ; do
+		sleep 1
+		counter=$((counter + 1))
+		[ "$counter" -gt "$limit" ] && exit 1
+	done
+
+	lock $lockfile
+	trap finish EXIT INT TERM
+}
+
+
+#####
+##### helper functions
+#####
+
+#given a an ip and a mask in the form of "192.168.1.1/24"
+#return the network address like "192.168.1.0/24"
+get_network_address()
+{
+	local ip="$1"
+	[ -z "$ip" ] && return
+
+	local prefix=${ip##*/}
+
+	local ip1=${ip%%.*} ; ip=${ip#*.*}
+	local ip2=${ip%%.*} ; ip=${ip#*.*}
+	local ip3=${ip%%.*} ; ip=${ip#*.*}
+	local ip4=${ip%%/*}
+
+	local ip=$((($ip1 << 24) + ($ip2 << 16) + ($ip3 << 8) + $ip4))
+	local mask=$((0xFFFFFFFF >> (32 - $prefix) << (32 - $prefix)))
+	local network=$(($ip & $mask))
+
+	local n1=$((($network & 0xFF000000) >> 24))
+	local n2=$((($network & 0x00FF0000) >> 16))
+	local n3=$((($network & 0x0000FF00) >> 8))
+	local n4=$(( $network & 0x000000FF))
+
+	echo "$n1.$n2.$n3.$n4/$prefix"
+}
+
+#given a network address (192.168.1.0/24)
+#find the next network address (192.168.2.0/24)
+next_network_address()
+{
+	local ip=$1
+	local prefix=${ip##*/}
+
+	local ip1=${ip%%.*} ; ip=${ip#*.*}
+	local ip2=${ip%%.*} ; ip=${ip#*.*}
+	local ip3=${ip%%.*} ; ip=${ip#*.*}
+	local ip4=${ip%%/*}
+
+	local ip=$((($ip1 << 24) + ($ip2 << 16) + ($ip3 << 8) + $ip4))
+	local one=$((1 << (32-$prefix)))
+	local new=$(($ip + $one))
+
+	local n1=$((($new & 0xFF000000) >> 24))
+	local n2=$((($new & 0x00FF0000) >> 16))
+	local n3=$((($new & 0x0000FF00) >> 8))
+	local n4=$(( $new & 0x000000FF))
+
+	echo "$n1.$n2.$n3.$n4/$prefix"
+}
+
+# given a network address and a prefix (192.168.2.0/24)
+# return the first host ip available   (192.168.2.1)
+first_host_in_network ()
+{
+	local ip=$1
+	local prefix=${ip##*/}
+
+	local ip1=${ip%%.*} ; ip=${ip#*.*}
+	local ip2=${ip%%.*} ; ip=${ip#*.*}
+	local ip3=${ip%%.*} ; ip=${ip#*.*}
+	local ip4=${ip%%/*}
+
+	local ip=$((($ip1 << 24) + ($ip2 << 16) + ($ip3 << 8) + $ip4))
+	local new=$(($ip + 1))
+
+	local n1=$((($new & 0xFF000000) >> 24))
+	local n2=$((($new & 0x00FF0000) >> 16))
+	local n3=$((($new & 0x0000FF00) >> 8))
+	local n4=$(( $new & 0x000000FF))
+
+	echo "$n1.$n2.$n3.$n4"
+}
+
+# given a network address,
+# find the next available network address.
+shift_range()
+{
+	local net="$1"
+	while true ; do
+		if [ "$restricted_nets" == "${restricted_nets//$net/}" ] && [ "$all_nets" == "${all_nets//$net/}" ]; then
+			# found a net that is not in restricted nets nor in all nets
+			break
+		fi
+		net=$(next_network_address $net)
+	done
+
+	echo "$net"
+}
+
+
+#####
+##### parse all interfaces section
+#####
+
+# restricted_nets = all the IPs on wan interfaces
+# all_nets = all the IPs on any interface
+parse_interface()
+{
+	local interface=$1
+	local nets=""		# "192.168.1.1/24"
+	local networks=""	# "192.168.1.0/24"
+
+	config_get is_lan $interface is_lan
+	network_get_subnets nets $interface
+
+	for n in $nets ; do
+		networks="$networks $(get_network_address $n)"
+	done
+
+	[ "$is_lan" != "1" ] && restricted_nets="$restricted_nets $networks"
+	all_nets="$all_nets $networks"
+}
+
+# parse all the interfaces
+# get all the IPs on wan interfaces and store them in restrict_nets
+# get all the IPs on all interfaces and store them in all_nets
+parse_interfaces()
+{
+	config_foreach parse_interface "interface"
+}
+
+
+#####
+##### parse all lan interfaces section
+#####
+
+parse_lan()
+{
+	local interface=$1
+	local nets=""
+	local ips=""
+	local newips=""
+	local ips_changed=0
+
+	[ "$interface" == "loopback" ] && return
+	config_get is_lan $interface is_lan
+	[ "$is_lan" == "1" ] || return
+
+	network_get_subnets ips $interface
+
+	for ip in $ips ; do
+		net="$(get_network_address $ip)"
+
+		if [ "$restricted_nets" == "${restricted_nets//$net/}" ] ; then
+			# net is not in restricted nets
+			# append ip to newips
+			[ -z "$newips" ] && newips="${ip%/*}" ||  newips="$newips ${ip%/*}"
+			continue
+		fi
+
+		#net is in restricted_nets
+		local newnet=$(shift_range $net)
+		local newip="$(first_host_in_network $newnet)"
+		# append newip to newips
+		[ -z "$newips" ] && newips="$newip" ||  newips="$newips $newip"
+
+		ips_changed=1
+		logger "$0: Changing the ip on interface $interface from $ip to $newip/${newnet##*/}"
+		echo "$0: Changing the ip on interface $interface from $ip to $newip/${newnet##*/}" >/dev/console
+	done
+
+	#assign the new ips
+	if [ "$ips_changed" == "1" ] ; then
+		uci -q set network.$interface.ipaddr="$newips"
+	fi
+}
+
+# parse all the interface with is_lan=1
+parse_lans()
+{
+	config_foreach parse_lan "interface"
+}
+
+
+#####
+##### main
+#####
+
+main()
+{
+	initial_check
+	just_one_instance
+
+	config_load network
+	parse_interfaces
+	parse_lans
+
+	if [ -n "$(uci changes network)" ] ; then
+		ubus call uci commit '{"config":"network"}'
+	fi
+}
+
+main $@

inteno-netmodes/files/etc/hotplug.d/net/80-repeater

@@ -3,6 +3,9 @@
 . /lib/functions.sh
 include /lib/network
 
+# exit if no wet interface is available
+uci show wireless | grep mode | grep -q wet || exit
+
 ps | grep hotplug | grep button && exit
 
 MTK=0
@@ -52,6 +55,7 @@ link=$(cat /sys/class/net/${WANDEV:0:4}/operstate)
 case "$ACTION" in
 	add|register)
 		[ "$link" == "down" ] && return
+		ubus call leds set  '{"state" : "allflash"}'
 		echo "Autoswitch to Extender mode" > /dev/console
 		sleep 2
 		wetif="$(get_wifi_wet_interface)"
@@ -66,10 +70,16 @@ case "$ACTION" in
 		uci set network.wan.ifname="$(echo $WANDEV $(uci get network.wan.ifname) | sed 's/$/ /' | sed -r "s/$wetif //g" | tr ' ' '\n' | sort -u | tr '\n' ' ')"
 		uci commit network
 		ubus call network reload
+		sleep 1
+		ubus call network.device set_state "{\"name\":\"$wetif\", \"defer\":true}"
+		[ -f /usr/sbin/wlctl ] && wlctl -i $wetif bss down 2>/dev/null
 		ping -c 1 -w 10 $defroute >/dev/null 2>&1 || killall -USR1 udhcpc
+		ubus call router.network reload
+		ubus call leds set  '{"state" : "normal"}'
 	;;
 	remove|unregister)
 		[ "$link" == "up" ] && return
+		ubus call leds set  '{"state" : "allflash"}'
 		echo "Autoswitch to Repeater mode" > /dev/console
 		sleep 2
 		wetif="$(get_wifi_wet_interface)"
@@ -84,10 +94,16 @@ case "$ACTION" in
 		uci set network.wan.ifname="$(echo $wetif $(uci get network.wan.ifname) | sed 's/$/ /' | sed -r "s/$WANDEV //g" | tr ' ' '\n' | sort -u | tr '\n' ' ')"
 		uci commit network
 		ubus call network reload
+		sleep 1
+		ubus call network.device set_state "{\"name\":\"$WANDEV\", \"defer\":true}"
+		[ -f /usr/sbin/wlctl ] && wlctl -i $wetif bss up 2>/dev/null
 		ping -c 1 -w 10 $defroute >/dev/null 2>&1 || {
 			killall -9 wifi
 			wifi reload nodat
 			killall -USR1 udhcpc
 		}
+		ubus call router.network reload
+		ubus call leds set  '{"state" : "normal"}'
 	;;
 esac
+

inteno-netmodes/files/etc/init.d/netmode

@@ -3,6 +3,9 @@
 START=10
 USE_PROCD=1
 
+TMPDIR=/var/netmodes
+OLD_MODE_FILE=/var/netmodes/old_mode
+
 . /usr/share/libubox/jshn.sh
 . /lib/network/config.sh
 
@@ -41,13 +44,29 @@ get_device() {
 
 populate_netmodes() {
 	[ -f /etc/config/netmode -a -d $modedir ] || return
+	local curmode
+
+	config_load netmode
+
+	config_get curmode setup curmode
+
+	mkdir -p $TMPDIR
+
+	if [ "$curmode" == "routed" ]; then
+		local hw="$(db -q get hw.board.hardware)"
+		if [ "$hw" == "EX400" ]; then
+			curmode="routed_mtk"
+		else
+			curmode="routed_brcm"
+		fi
+	fi
+
+	echo $curmode > $OLD_MODE_FILE
 
 	delete_netmode() {
 		uci delete netmode.$1
 	}
 
-	config_load netmode
-
 	config_foreach delete_netmode netmode
 	uci commit netmode
 
@@ -162,17 +181,20 @@ populate_netmodes() {
 
 switch_netmode() {
 	[ -f /etc/config/netmode -a -d $modedir ] || return
-	local curmode conf repeaterready
+
+	local netreload="$1"
+	local curmode conf repeaterready old_mode
 
 	config_load netmode
 
+	config_get curmode setup curmode
+
 	config_get repeaterready setup repeaterready "0"
 	if [ "$repeaterready" == "1" ] ; then
 		uci -q set netmode.setup.repeaterready="0"
 		uci commit netmode
 	fi
 
-	config_get curmode setup curmode
 	if [ "$curmode" == "repeater" ]; then
 		local hw="$(db -q get hw.board.hardware)"
 		if [ "$hw" == "EX400" ]; then
@@ -193,6 +215,17 @@ switch_netmode() {
 		uci set netmode.setup.curmode="$curmode"
 		uci commit netmode
 	fi
+
+	old_mode=`cat $OLD_MODE_FILE 2>/dev/null`
+
+        # if curmode has not changed do not copy configs
+        if [ "$curmode" == "$old_mode" ]; then
+                /etc/init.d/enviroment reload
+                return
+        fi
+
+        echo $curmode >$OLD_MODE_FILE
+
 	[ -d "/etc/netmodes/$curmode" ] || return
 	cp /etc/netmodes/$curmode/* /etc/config/
 	rm -f /etc/config/DETAILS
@@ -201,19 +234,35 @@ switch_netmode() {
 	local askcred=$(uci -q get netmode.$curmode.askcred)
 	if [ "$reboot" == "0" ]; then
 		/etc/init.d/enviroment reload
+		case "$curmode" in
+			routed*)
+				ubus call uci commit '{"config":"network"}'
+			;;
+			repeater*)
+				if [ -f /etc/init.d/omcproxy ]; then
+					/etc/init.d/omcproxy stop
+				fi
+				if [ "$netreload" != "0" ]; then
+					ubus call uci commit '{"config":"network"}'
+				fi
+			;;
+		esac
 	else
 		reboot &
 	fi
 }
 
 start_client_listener() {
-	local curmode repeaterready
-	config_load netmode
+	local curmode repeaterready ulcpid
 
+	config_load netmode
 	config_get repeaterready setup repeaterready 0
 
+	ulcpid=$(ps | grep "ubus listen client" | grep -v grep | awk '{print$1}')
+
 	[ $repeaterready -eq 1 ] && {
 		killall -SIGKILL netmode-client-detect >/dev/null 2>&1
+		kill -9 $ulcpid >/dev/null 2>&1
 		return
 	}
 
@@ -222,6 +271,7 @@ start_client_listener() {
 	case "$curmode" in
 		repeater*)
 			killall -SIGKILL netmode-client-detect >/dev/null 2>&1
+			kill -9 $ulcpid >/dev/null 2>&1
 		;;
 		*)
 			pidof netmode-client-detect || /sbin/netmode-client-detect &
@@ -229,23 +279,45 @@ start_client_listener() {
 	esac
 }
 
+start_netmode_discover() {
+	local curmode repeaterready
+
+	killall -9 netmode-discover >/dev/null 2>&1
+
+	config_load netmode
+	config_get repeaterready setup repeaterready 0
+
+	[ $repeaterready -eq 1 ] && return
+
+	config_get curmode setup curmode
+
+	case "$curmode" in
+		repeater*)
+			/sbin/netmode-discover &
+		;;
+	esac
+}
+
 start_service() {
 	populate_netmodes
 	start_client_listener
+	start_netmode_discover
 }
 
 reload_service() {
-        switch_netmode
+        switch_netmode "$1"
 
 	# set default JUCI page to overview
 	uci -q set juci.juci.homepage="overview"
 	uci commit juci
 
 	start_client_listener
+	start_netmode_discover
 }
 
 stop_service() {
 	killall -SIGKILL netmode-client-detect >/dev/null 2>&1
+	killall -9 netmode-discover >/dev/null 2>&1
 }
 
 service_triggers()

inteno-netmodes/files/etc/netmodes/bridged/wireless

@@ -4,6 +4,13 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device 'wl0'
 	option type 'broadcom'
 	option country 'EU/13'

inteno-netmodes/files/etc/netmodes/internet_iptv_voip/DETAILS

@@ -11,7 +11,8 @@
 	"excluded_boards" : [
 		"CG300",
 		"CG301",
-		"EX400"
+		"EX400",
+		"F*"
 	],
 	"acl" : [
 		"admin",

inteno-netmodes/files/etc/netmodes/internet_iptv_voip/wireless

@@ -4,6 +4,13 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device 'wl0'
 	option type 'broadcom'
 	option country 'EU/13'

inteno-netmodes/files/etc/netmodes/one_bridged_port/DETAILS

@@ -0,0 +1,16 @@
+{
+	"description": [
+		{ "en" : "Routed, LAN1 bridged" },
+		{ "sv" : "Routed, LAN1 bryggad" }
+
+	],
+	"explanation": [
+		{ "en" : "LAN4 port is bridged with internet" },
+                { "sv" : "LAN4 port överbryggas med internet" }
+	],
+	"excluded_boards" : [
+		"EX4*"
+	],
+	"credentials" : 0
+}
+

inteno-netmodes/files/etc/netmodes/one_bridged_port/network

@@ -0,0 +1,31 @@
+
+config interface 'loopback'
+	option is_lan '1'
+	option ifname 'lo'
+	option proto 'static'
+	option ipaddr '127.0.0.1'
+	option netmask '255.0.0.0'
+
+config interface 'lan'
+	option is_lan '1'
+	option type 'bridge'
+	option proto 'static'
+	option ipaddr '192.168.1.1'
+	option netmask '255.255.255.0'
+	option ifname '$LAN2 $LAN3 $LAN4'
+	option ip6assign '64'
+	
+config interface 'wan'
+	option type 'bridge'
+	option proto 'dhcp'
+	option vendorid '$HARDWAREID-INTENO'
+	option hostname 'Inteno_$MAC4'
+	option ifname '$WAN.1 $LAN1'
+	option reqopts '43 66 67 128 132 224 225 226'
+
+config interface 'wan6'
+	option proto 'dhcpv6'
+	option ifname '@wan'
+	option reqaddress 'try'
+	option reqprefix 'auto'
+

inteno-netmodes/files/etc/netmodes/repeater_brcm_2g_up_5g_down/DETAILS

@@ -11,12 +11,10 @@
 		"DG15*",
 		"DG40*",
 		"EG40*",
-		"EX40*"
-	],
-	"acl" : [
-		"admin"
+		"EX40*",
+		"F*"
 	],
 	"uplink_band" : "b",
 	"credentials" : 1,
-	"reboot" : 0
+	"reboot" : 1
 }

inteno-netmodes/files/etc/netmodes/repeater_brcm_2g_up_5g_down/wireless

@@ -4,6 +4,13 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device 'wl0'
 	option type 'broadcom'
 	option country 'EU/13'
@@ -27,7 +34,7 @@ config wifi-device 'wl0'
 	option rifs '0'
 	option rifs_advert '0'
 	option maxassoc '32'
-	option beamforming '0'
+	option beamforming '1'
 	option doth '1'
 	option dfsc '1'
 
@@ -70,17 +77,4 @@ config wifi-device 'wl1'
 	option rifs_advert '0'
 	option maxassoc '32'
 	option doth '0'
-	option apsta '1'
-
-config wifi-iface
-	option device 'wl1'
-	option ifname 'wl1'
-	option network 'wan'
-	option mode 'wet'
-	option ssid 'Inteno-$BSSID4'
-	option encryption 'psk2'
-	option cipher 'auto'
-	option wps_pbc '0'
-	option wmf_bss_enable '1'
-	option autoconf '1'
 

inteno-netmodes/files/etc/netmodes/repeater_brcm_2g_up_dual_down/DETAILS

@@ -11,12 +11,10 @@
 		"DG15*",
 		"DG40*",
 		"EG40*",
-		"EX40*"
-	],
-	"acl" : [
-		"admin"
+		"EX40*",
+		"F*"
 	],
 	"uplink_band" : "b",
 	"credentials" : 1,
-	"reboot" : 0
+	"reboot" : 1
 }

inteno-netmodes/files/etc/netmodes/repeater_brcm_2g_up_dual_down/wireless

@@ -4,6 +4,13 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device 'wl0'
 	option type 'broadcom'
 	option country 'EU/13'
@@ -27,7 +34,7 @@ config wifi-device 'wl0'
 	option rifs '0'
 	option rifs_advert '0'
 	option maxassoc '32'
-	option beamforming '0'
+	option beamforming '1'
 	option doth '1'
 	option dfsc '1'
 
@@ -70,19 +77,6 @@ config wifi-device 'wl1'
 	option rifs_advert '0'
 	option maxassoc '32'
 	option doth '0'
-	option apsta '1'
-
-config wifi-iface
-	option device 'wl1'
-	option ifname 'wl1'
-	option network 'wan'
-	option mode 'wet'
-	option ssid 'Inteno-$BSSID4'
-	option encryption 'psk2'
-	option cipher 'auto'
-	option wps_pbc '0'
-	option wmf_bss_enable '1'
-	option autoconf '1'
 
 config wifi-iface
 	option device 'wl1'

inteno-netmodes/files/etc/netmodes/repeater_mtk_2g_up_dual_down/DETAILS

@@ -8,9 +8,10 @@
 		{ "sv" : "Routern kommer att fungera som en trådbunden extender eller trådlös repeater till den valda trådlösa åtkomstpunkten. Uplink 2.4G & Downlink 2.4G + 5G" }
 	],
 	"excluded_boards" : [
-		"*G*"
+		"*G*",
+		"F*"
 	],
 	"uplink_band" : 'b',
 	"credentials" : 1,
-	"reboot" : 0
+	"reboot" : 1
 }

inteno-netmodes/files/etc/netmodes/repeater_mtk_2g_up_dual_down/wireless

@@ -4,14 +4,20 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device  ra0
 	option band b
-	option channel  1
+	option channel  auto
 	option bandwidth '20'
-	option hwmode   11n
+	option hwmode   auto
 	option htmode   HT20
 	option country 'DE'
-	option beamforming 0
 
 config wifi-iface
 	option device   ra0
@@ -21,6 +27,7 @@ config wifi-iface
 	option encryption psk2
 	option key      $WPAKEY
 	option ifname	ra0
+	option wps_pbc	1
 
 config wifi-device  rai0
 	option band a
@@ -29,7 +36,7 @@ config wifi-device  rai0
 	option hwmode   11ac
 	option htmode   VHT80
 	option country 'DE'
-	option beamforming 0
+	option beamforming 1
 
 config wifi-iface
 	option device   rai0
@@ -39,6 +46,7 @@ config wifi-iface
 	option encryption psk2
 	option key      $WPAKEY
 	option ifname	rai0
+	option wps_pbc	1
 
 config wifi-iface
 	option device   ra0

inteno-netmodes/files/etc/netmodes/repeater_mtk_5g_up_dual_down/DETAILS

@@ -8,9 +8,10 @@
 		{ "sv" : "Routern kommer att fungera som en trådbunden extender eller trådlös repeater till den valda trådlösa åtkomstpunkten. Uplink 5G & Downlink 2.4G + 5G" }
 	],
 	"excluded_boards" : [
-		"*G*"
+		"*G*",
+		"F*"
 	],
 	"uplink_band" : 'a',
 	"credentials" : 1,
-	"reboot" : 0
+	"reboot" : 1
 }

inteno-netmodes/files/etc/netmodes/repeater_mtk_5g_up_dual_down/wireless

@@ -4,14 +4,20 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device  ra0
 	option band b
 	option channel  auto
 	option bandwidth '20'
-	option hwmode   11n
+	option hwmode   auto
 	option htmode   HT20
 	option country 'DE'
-	option beamforming 0
 
 config wifi-iface
 	option device   ra0
@@ -21,15 +27,16 @@ config wifi-iface
 	option encryption psk2
 	option key      $WPAKEY
 	option ifname	ra0
+	option wps_pbc	1
 
 config wifi-device  rai0
 	option band a
-	option channel  36
+	option channel  auto
 	option bandwidth '80'
 	option hwmode   11ac
 	option htmode   VHT80
 	option country 'DE'
-	option beamforming 0
+	option beamforming 1
 
 config wifi-iface
 	option device   rai0
@@ -39,6 +46,7 @@ config wifi-iface
 	option encryption psk2
 	option key      $WPAKEY
 	option ifname	rai0
+	option wps_pbc	1
 
 config wifi-iface
 	option device   rai0

inteno-netmodes/files/etc/netmodes/routed_brcm/wireless

@@ -4,6 +4,13 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device 'wl0'
 	option type 'broadcom'
 	option country 'EU/13'

inteno-netmodes/files/etc/netmodes/routed_mtk/DETAILS

@@ -8,8 +8,10 @@
 		{ "sv" : "" }
 	],
 	"excluded_boards" : [
-		"*G*"
+		"*G*",
+		"F*"
 	],
+	"reboot" : 0,
 	"credentials" : 0
 }
 

inteno-netmodes/files/etc/netmodes/routed_mtk/omcproxy

@@ -0,0 +1,10 @@
+config proxy
+	option scope global
+	option uplink wan
+	list downlink lan
+
+config proxy
+	option scope global
+	option uplink wan6
+	list downlink lan
+

inteno-netmodes/files/etc/netmodes/routed_mtk/wireless

@@ -4,14 +4,20 @@ config wifi-status 'status'
 	option sched_status '0'
 	option schedule '0'
 
+config bandsteering 'bandsteering'
+	option enabled '0'
+	option policy '0'
+
+config apsteering 'apsteering'
+	option enabled '0'
+
 config wifi-device  ra0
 	option band b
-	option channel  1
+	option channel  auto
 	option bandwidth '20'
-	option hwmode   11n
+	option hwmode   auto
 	option htmode   HT20
 	option country 'DE'
-	option beamforming 0
 
 config wifi-iface
 	option device   ra0
@@ -20,15 +26,16 @@ config wifi-iface
 	option ssid     Inteno-$BSSID4
 	option encryption psk2
 	option key      $WPAKEY
+	option wps_pbc	1
 
 config wifi-device  rai0
 	option band a
-	option channel  36
+	option channel  auto
 	option bandwidth '80'
 	option hwmode   11ac
 	option htmode   VHT80
 	option country 'DE'
-	option beamforming 0
+	option beamforming 1
 
 config wifi-iface
 	option device   rai0
@@ -37,4 +44,5 @@ config wifi-iface
 	option ssid     Inteno-$BSSID4
 	option encryption psk2
 	option key      $WPAKEY
+	option wps_pbc	1
 

inteno-netmodes/files/sbin/netmode-client-detect

@@ -9,28 +9,49 @@ local action ipaddr macaddr network
 
 timed_check() {
 	while true; do
+		network=${network:-lan}
+		ubus call repeater get_creds '{"network":"'$network'","file":"/tmp/wificontrol.txt"}'
 		wificontrol --router
 		sleep $1
 	done
 }
 
+is_inteno_macaddr()
+{
+	macaddr=$1
+
+	echo $macaddr | grep -i -e "^00:22:07" \
+				-e "^02:22:07" \
+				-e "^44:D4:37" \
+				-e "^00:0C:07" \
+				-e "^02:0C:07" \
+				-e "^06:0C:07" \
+				-e "^00:0C:43" \
+				-e "^02:0C:43" \
+				-e "^06:0C:43" \
+				-e "^34:E3:80" \
+	&& return
+	false
+}
 
 timed_check 60 &
 
-ubus listen client | \
-while read event ; do
-	#echo "netmode-client-detect got event: $event" >/dev/console
-	json_load "$event"
-	json_select client
-	json_get_var action action
-	[ "$action" == "connect" ] || continue
-	json_get_var macaddr macaddr
-	json_get_var ipaddr ipaddr
-	json_get_var network netwrork "lan"
+while true ; do
+	ubus listen client | \
+	while read event ; do
+		#echo "netmode-client-detect got event: $event" >/dev/console
+		json_load "$event"
+		json_select client
+		json_get_var action action
+		[ "$action" == "connect" ] || continue
+		json_get_var macaddr macaddr
+		json_get_var ipaddr ipaddr
+		json_get_var network network "lan"
 
-	if echo $macaddr | grep -i -e "^00:22:07" -e "^44:D4:37" -e "^02:0C:07" -e "^06:0C:07"; then
-		echo "netmode-client-detect: a new Inteno device detected on '$network' network (MACAddr:$macaddr IPAddr:$ipaddr)" >/dev/console
-		ubus call repeater get_creds '{"network":"'$network'","file":"/tmp/wificontrol.txt"}'
-		/sbin/wificontrol --router --destination $ipaddr
-	fi
+		if is_inteno_macaddr $macaddr; then
+			echo "netmode-client-detect: a new Inteno device detected on '$network' network (MACAddr:$macaddr IPAddr:$ipaddr)" >/dev/console
+			ubus call repeater get_creds '{"network":"'$network'","file":"/tmp/wificontrol.txt"}'
+			/sbin/wificontrol --router --destination $ipaddr
+		fi
+	done
 done

inteno-netmodes/files/sbin/netmode-conf

@@ -63,7 +63,7 @@ get_iface_num() {
 			break
 		fi
 		mode="$(uci -q get wireless.@wifi-iface[$i].mode)"
-		if [ "$mode" != "ap" ]; then
+		if [ "$mode" == "wet" -o "$mode" == "sta" ]; then
 			i=$((i+1))
 			continue
 		fi
@@ -108,9 +108,16 @@ backup() {
 file="$1"
 from_gui="$2"
 
-
 [ -f "$file" ] || exit
 
+# let netmode-handler up to 20 seconds to finish switching mode
+for tm in 2 4 6 8; do
+	if [ ! -f /tmp/switching_mode ]; then
+		break
+	fi
+	sleep $tm
+done
+
 [ "$from_gui" == "true" ] && backup
 
 json_load "`cat $file`"
@@ -143,29 +150,26 @@ local dummy band ssid key encryption device iface_num
 while json_get_var dummy $i; do
 	json_select $i
 	json_get_var band band
-	[ "$apcliband" == "$band" ] && break
+	[ "$band" == "" -o "$apcliband" == "$band" ] && break
 	json_select ..
 	i=$((i+1))
 done
 
-[ "$apcliband" == "$band" ] || {
+[ "$apcliband" == "$band" -o "$band" == "" ] || {
 	[ "$from_gui" == "true" ] && restore "back"
 	exit
 }
 
 repeater_iface_num=$(uci -q show wireless | grep -e ".mode='wet'" -e ".mode='sta'"  | sed 's/.*\[\([0-9]\)\].*/\1/')
 
-[ -z "$repeater_iface_num" ] && {
-	[ "$from_gui" == "true" ] && restore "back"
-	exit
+[ "$repeater_iface_num" ] && {
+	json_get_var ssid ssid
+	json_get_var key key
+	json_get_var encryption encryption
+
+	set_wireless_values "$repeater_iface_num" "$ssid" "$key" "$encryption"
 }
 
-json_get_var ssid ssid
-json_get_var key key
-json_get_var encryption encryption
-
-set_wireless_values "$repeater_iface_num" "$ssid" "$key" "$encryption"
-
 json_load "`cat $file`"
 json_select "wifi_ifaces"
 
@@ -177,30 +181,61 @@ i=1
 while json_get_var dummy $i; do
 	json_select $i
 	json_get_var band band
-	get_device "$band" device
-	case $band in
-		a)
-			get_iface_num "$device" "$a_num" iface_num
-			a_num=$((a_num+1))
-			;;
-		b)
-			get_iface_num "$device" "$b_num" iface_num
-			b_num=$((b_num+1))
-			;;
-	esac
-	[ -z $iface_num ] && {
-		[ "$from_gui" == "true" ] && restore "back"
-		exit
-	}
 	json_get_var ssid ssid
 	json_get_var encryption encryption
 	json_get_var key key
-	set_wireless_values "$iface_num" "$ssid" "$key" "$encryption" "$device"
-	json_select ..
+	if [ "$band" == "" ]; then
+		get_device "a" device
+		get_iface_num "$device" "$a_num" iface_num
+		a_num=$((a_num+1))
+		[ -z $iface_num ] && {
+			[ "$from_gui" == "true" ] && restore "back"
+			exit
+		}
+		set_wireless_values "$iface_num" "$ssid" "$key" "$encryption" "$device"
+		get_device "b" device
+                get_iface_num "$device" "$b_num" iface_num
+                b_num=$((b_num+1))
+                [ -z $iface_num ] && {
+                        [ "$from_gui" == "true" ] && restore "back"
+                        exit
+                }
+		set_wireless_values "$iface_num" "$ssid" "$key" "$encryption" "$device"
+	else
+		get_device "$band" device
+		case $band in
+			a)
+				get_iface_num "$device" "$a_num" iface_num
+				a_num=$((a_num+1))
+				;;
+			b)
+				get_iface_num "$device" "$b_num" iface_num
+				b_num=$((b_num+1))
+				;;
+		esac
+		[ -z $iface_num ] && {
+			[ "$from_gui" == "true" ] && restore "back"
+			exit
+		}
+		set_wireless_values "$iface_num" "$ssid" "$key" "$encryption" "$device"
+	fi
 	i=$((i+1))
+	json_select ..
 done
 
+if [ -z $repeater_iface_num ] ; then
+	i=$((b_num + a_num))
+else
+	i=$((b_num + a_num + 1))
+fi
+
+if [ $repeater_iface_num -gt $i ]; then
+	i=$((i-1))
+fi
+
 while uci -q get wireless.@wifi-iface[$i] >/dev/null; do
+	# if repeater_iface_num is greater than the number of
+	# configured downlink we need to make sure its not deleted
 	local mode="$(uci -q get wireless.@wifi-iface[$i].mode)"
 	if [ "$mode" == "wet" -o "$mode" == "sta" ]; then
 		i=$((i+1))
@@ -208,7 +243,8 @@ while uci -q get wireless.@wifi-iface[$i] >/dev/null; do
 	fi
 	state="reload"
 	uci -q delete wireless.@wifi-iface[$i] >/dev/null
-	i=$((i+1))
+	# do not increment i. The next interface will now
+	# have the same index as the deleted interface
 done
 
 uci commit wireless
@@ -239,7 +275,9 @@ if [ "$from_gui" == "true" ]; then
 else
 	if [ "$state" == "exit" ]; then
 		return
-	elif [ "$state" == "apply" ]; then
+	fi
+	ubus call leds set '{"state":"allflash"}'
+	if [ "$state" == "apply" ]; then
 		# wifi apply
 		wifi reload
 	else
@@ -247,4 +285,5 @@ else
 		wifi reload
 	fi
 	[ -f /etc/init.d/layer2_interface_ethernet -a -f /etc/config/layer2_interface_ethernet ] && /etc/init.d/layer2_interface_ethernet reload
+	ubus call leds set '{"state":"normal"}'
 fi

inteno-netmodes/files/sbin/netmode-discover

@@ -0,0 +1,44 @@
+#!/bin/sh
+
+local unlisted mac ipaddr netmask mask
+
+mask_to_cidr() {
+    nbits=0
+    IFS=.
+    for dec in $1 ; do
+        case $dec in
+            255) let nbits+=8;;
+            254) let nbits+=7;;
+            252) let nbits+=6;;
+            248) let nbits+=5;;
+            240) let nbits+=4;;
+            224) let nbits+=3;;
+            192) let nbits+=2;;
+            128) let nbits+=1;;
+            0);;
+            *) echo "Error: $dec is not recognised"; exit 1
+        esac
+    done
+    echo "$nbits"
+}
+
+while true; do
+	unlisted=0
+
+	ps | grep -q wifi | grep -q reload || {
+		for mac in $(brctl showmacs br-wan 2>/dev/null | tail -n +2 | grep no | awk '{print$2}'); do
+			grep -q "$mac" /proc/net/arp || unlisted=$((unlisted+1))
+		done
+
+		ipaddr=$(ifconfig br-wan | grep -v inet6 | grep inet | tr ':' ' ' | awk '{print$3}')
+		netmask=$(ifconfig br-wan | grep -v inet6 | grep inet | tr ':' ' ' | awk '{print$7}')
+		mask=$(mask_to_cidr $netmask)
+	}
+
+	if [ $unlisted -gt 0 -a -n "$ipaddr" -a -n "$netmask" ]; then
+		fping -c 1 -t 1000 -g $ipaddr/$mask -q >/dev/null 2>&1
+	fi
+
+	sleep 40
+done
+

inteno-netmodes/files/usr/libexec/rpcd/repeater

@@ -7,7 +7,7 @@ get_if_creds() {
 	local section=$1
 	local network=$2
 	local net dev ssid key encryption band
-	config_get net $section "network"
+	config_get net $section "network" "lan"
 	if [ "$net" == "$network" ]; then
 		config_get dev $section "device"
 		band="$(uci -q get wireless.$dev.band)"
@@ -15,7 +15,6 @@ get_if_creds() {
 		config_get key $section key
 		config_get encryption $section encryption
 		config_get disabled $section disabled 0
-		echo "disabled for $band = $disabled" >>/tmp/dbg
 		[ $disabled -eq 1 ] && return
 		[ "$ssid" == "" -o "$band" == "" ] && return
 		json_add_object

iop/configs/config

@@ -3,7 +3,7 @@ CONFIG_BUSYBOX_CUSTOM=y
 CONFIG_CCACHE=y
 CONFIG_DEBUG=y
 CONFIG_DEVEL=y
-CONFIG_LOCALMIRROR="http://mirror.inteno.se/mirror"
+# CONFIG_LOCALMIRROR is not set
 CONFIG_PACKAGE_6in4=y
 CONFIG_PACKAGE_6rd=y
 CONFIG_PACKAGE_6to4=y
@@ -56,6 +56,7 @@ CONFIG_PACKAGE_juci-dropbear=y
 CONFIG_PACKAGE_juci-ethernet=y
 CONFIG_PACKAGE_juci-event=y
 CONFIG_PACKAGE_juci-firewall-fw3=y
+CONFIG_PACKAGE_juci-ice-client=y
 CONFIG_PACKAGE_juci-icwmp=y
 CONFIG_PACKAGE_juci-igmpinfo=y
 CONFIG_PACKAGE_juci-inteno-backup=y
@@ -71,6 +72,7 @@ CONFIG_PACKAGE_juci-natalie-dect=y
 CONFIG_PACKAGE_juci-netmode=y
 CONFIG_PACKAGE_juci-network-netifd=y
 CONFIG_PACKAGE_juci-owsd=y
+CONFIG_PACKAGE_juci-openvpn=y
 CONFIG_PACKAGE_juci-printer=y
 CONFIG_PACKAGE_juci-realtime-graphs=y
 CONFIG_PACKAGE_juci-samba=y
@@ -94,6 +96,7 @@ CONFIG_PACKAGE_libdaemon=y
 CONFIG_PACKAGE_libffmpeg-mini=y
 CONFIG_PACKAGE_libgmp=y
 CONFIG_PACKAGE_libreadline=y
+CONFIG_PACKAGE_loop-detector=m
 CONFIG_PACKAGE_minidlna=y
 CONFIG_PACKAGE_miniupnpd=y
 CONFIG_PACKAGE_mtd-utils=y
@@ -109,12 +112,13 @@ CONFIG_PACKAGE_odhcpd=y
 CONFIG_PACKAGE_openssl-util=y
 CONFIG_PACKAGE_openvpn-easy-rsa=y
 CONFIG_PACKAGE_openvpn-openssl=y
-CONFIG_PACKAGE_p910nd=y
+# CONFIG_PACKAGE_p910nd is not set
 CONFIG_PACKAGE_peripheral_manager=y
 CONFIG_PACKAGE_port-management=y
 CONFIG_PACKAGE_power-management=y
 CONFIG_PACKAGE_ppp-mod-pppoa=y
 CONFIG_PACKAGE_ppp-mod-pppol2tp=y
+CONFIG_PACKAGE_ppp-mod-pptp=y
 CONFIG_PACKAGE_ppp-multilink=y
 # CONFIG_PACKAGE_ppp is not set
 CONFIG_PACKAGE_qos-scripts=y
@@ -156,12 +160,21 @@ CONFIG_BUSYBOX_CONFIG_FEATURE_UDHCP_8021Q=y
 CONFIG_BUSYBOX_CONFIG_FIRST_SYSTEM_ID=100
 CONFIG_BUSYBOX_CONFIG_HTTPD=y
 CONFIG_BUSYBOX_CONFIG_INSMOD=y
+CONFIG_BUSYBOX_CONFIG_MODINFO=y
+CONFIG_BUSYBOX_CONFIG_MODPROBE=y
+CONFIG_BUSYBOX_CONFIG_FEATURE_MODPROBE_BLACKLIST=y
+CONFIG_BUSYBOX_CONFIG_FEATURE_CHECK_TAINTED_MODULE=y
+CONFIG_BUSYBOX_CONFIG_FEATURE_MODUTILS_ALIAS=y
+CONFIG_BUSYBOX_CONFIG_FEATURE_MODUTILS_SYMBOLS=y
+CONFIG_BUSYBOX_CONFIG_DEFAULT_MODULES_DIR="/lib/modules"
+CONFIG_BUSYBOX_CONFIG_DEFAULT_DEPMOD_FILE="modules.dep"
 CONFIG_BUSYBOX_CONFIG_LAST_SYSTEM_ID=999
 CONFIG_BUSYBOX_CONFIG_LOGIN=y
 CONFIG_BUSYBOX_CONFIG_LSMOD=y
 CONFIG_BUSYBOX_CONFIG_LSPCI=y
 CONFIG_BUSYBOX_CONFIG_LSUSB=y
 CONFIG_BUSYBOX_CONFIG_MICROCOM=y
+CONFIG_BUSYBOX_CONFIG_MPSTAT=y
 CONFIG_BUSYBOX_CONFIG_RMMOD=y
 CONFIG_BUSYBOX_CONFIG_STTY=y
 CONFIG_BUSYBOX_CONFIG_TFTP=y

iop/iop.completion

@@ -5,14 +5,14 @@
 
 _iop_get_profiles()
 {
-    find feeds/feed_inteno_targets/iopsys-*/ -name '*.diff' \
+    find feeds/targets/iopsys-*/ -name '*.diff' \
         |awk -F'/' '{print$NF}' \
         |awk -F. '{print$1}'
 }
 
 _iop_get_models()
 {
-    find feeds/feed_inteno_targets/iopsys-*/ -mindepth 1 -maxdepth 1 -type d \
+    find feeds/targets/iopsys-*/ -mindepth 1 -maxdepth 1 -type d \
         |awk -F'/' '{print$NF}' \
         |egrep '^(cg|dg|eg|vg|vox)[0-9]'
 }
@@ -36,7 +36,7 @@ _iop()
              feeds_update genconfig generate_tarballs install_key \
              scp_changes setup_host ssh_install_key ssh_sysupgrade \
              ssh_sysupgrade_latest ssh_sysupgrade_latest_w status \
-             update_package"
+             update_package update_feed_branches"
 
     if [ $COMP_CWORD -eq 1 ] ; then
 

iop/scripts/extract_core.sh

@@ -6,15 +6,12 @@ function extract_core {
 	topdir=$(pwd)
 
 	# Paths to packages that should be exported.
-	paths+='package/network/services/samba36 '
+	paths+='package/network/services/base-files '
 	paths+='package/network/services/dnsmasq '
-	paths+='package/network/services/dropbear '
-	paths+='package/network/services/odhcpd '
 	paths+='package/network/config/firewall '
 	paths+='package/network/config/netifd '
 	paths+='package/network/config/qos-scripts '
-	paths+='package/network/utils/iproute2 '
-	paths+='package/network/utils/curl '
+	paths+='package/system/procd '
 	paths+='package/utils/busybox '
 
 	function print_usage {

iop/scripts/feeds_update.sh

@@ -28,14 +28,14 @@ function feeds_update {
 
     # replace core packages with iopsys versions
     if [ $override == 1 ]; then
-	./scripts/feeds install -f -p feed_inteno_openwrt -a
+	./scripts/feeds install -f -p openwrt_cc_core -a
     fi
 
     # targets need to be installed explicitly
     ./scripts/feeds install -p feed_inteno_targets iopsys-brcm63xx-mips
     ./scripts/feeds install -p feed_inteno_targets iopsys-brcm63xx-arm
     ./scripts/feeds install -p feed_inteno_targets iopsys-ramips
-    
+
     # install all packages
     ./scripts/feeds install -a 
 
@@ -54,6 +54,3 @@ function feeds_update {
 
 register_command "feeds_update" "Update feeds to point to commit hashes from feeds.conf"
 
-
-
-

iop/scripts/genconfig.sh

@@ -7,16 +7,15 @@ function genconfig {
 	export FILEDIR="files/"
 	export THEMEDIR="themes"
 	CURRENT_CONFIG_FILE=".current_config_file"
-	export CONFIGPATH="package/feeds/feed_inteno_packages/iop/configs"
+	export CONFIGPATH="package/feeds/iopsys/iop/configs"
 	CUSTPATH="customerconfigs"
-	CUSTREPO="git@private.inteno.se:customerconfigs"
 	export CUSTCONF="customerconfigs/customers"
 	export VERBOSE=0
 	export DEVELOPER=0
 	LOCAL_MIRROR="http://mirror.inteno.se/mirror"
 
-	iopsys_brcm63xx_mips="cg300 cg301 dg150 dg150v2 dg150alv2 dg200 dg200al dg301 dg301al eg300 vg50 vox25"
-	iopsys_brcm63xx_arm="dg400 eg400"
+	iopsys_brcm63xx_mips="cg300 cg301 dg150 dg150v2 dg150alv2 dg200 dg200al dg301 dg301al eg300 vg50 vox25 hpc_hu02 eg200"
+	iopsys_brcm63xx_arm="dg400 eg400 sdx_500rg f104w f104 dg400prime dg400primeb 963138REF_P502"
 	iopsys_ramips="ex400"
 	ramips="mt7621"
 	target="bogus"
@@ -156,15 +155,17 @@ function genconfig {
 
 	setup_dirs()
 	{
-		if [ $DEVELOPER -eq 1 ]; then
+		if ssh -o ConnectTimeout=5 git@private.inteno.se 2>/dev/null  | grep -qw ${CUSTREPO:22}; then
 			if [ ! -d "$CUSTPATH" ]; then
-			git clone "$CUSTREPO" "$CUSTPATH"
+				git clone "$CUSTREPO" "$CUSTPATH"
 			elif [ $IMPORT -eq 1 ]; then
-			cd $CUSTPATH
-			v "git pull"
-			git pull
-			cd - >/dev/null #go back
+				cd $CUSTPATH
+				v "git pull"
+				git pull
+				cd - >/dev/null #go back
 			fi
+		else
+			echo "You do not have access to $CUSTREPO"
 		fi
 
 		if [ ! -d "$FILEDIR" ]; then
@@ -192,9 +193,18 @@ function genconfig {
 		if [ $target == "bogus" ]; then
 			echo "Hardware profile does not exist"
 			exit 1
-		elif [ -n "$CUSTOMER" -a ! -d "$CUSTCONF/$CUSTOMER/$BOARDTYPE/" ]; then
-			echo "Customer profile does not exist"
-			exit 1
+		elif [ -n "$CUSTOMER" ]; then
+			if [ ! -d "$CUSTCONF/$CUSTOMER/" ]; then
+				echo "Customer profile for '$CUSTOMER' does not exist"
+				exit 1
+			elif [ ! -d "$CUSTCONF/$CUSTOMER/$BOARDTYPE/" ]; then
+				echo "'$BOARDTYPE' board profile does not exist for customer '$CUSTOMER'"
+				if [ -f "$CUSTCONF/$CUSTOMER/common/common.diff" ]; then
+					echo "Common profile configuration will be used"
+				else
+					exit 1
+				fi
+			fi
 		fi
 
 		# Generate base config
@@ -266,9 +276,9 @@ function genconfig {
 		[ $SRCTREEOVERR -eq 1 ] && echo CONFIG_SRC_TREE_OVERRIDE=y >> .config
 
 		# developer mode selected ?
+		echo "CONFIG_DEVEL=y" >>.config
 		if [ $DEVELOPER -eq 1 ]; then
 			# rewrite url to clone with ssh instead of http
-			echo "CONFIG_DEVEL=y" >>.config
 			echo "CONFIG_GITMIRROR_REWRITE=y" >>.config
 			[ $bcmAllowed -eq 0 ] && echo "CONFIG_BCM_OPEN=y" >> .config
 			[ $iceAllowed -eq 0 ] && echo "CONFIG_ICE_OPEN=y" >> .config
@@ -276,7 +286,6 @@ function genconfig {
 			[ $natalieAllowed -eq 0 ] && echo "CONFIG_NATALIE_OPEN=y" >> .config
 			[ $mediatekAllowed -eq 0 ] && echo "CONFIG_MEDIATEK_OPEN=y" >> .config
 		else
-			echo "CONFIG_DEVEL=n" >>.config
 			echo "CONFIG_GITMIRROR_REWRITE=n" >>.config
 			echo "CONFIG_BCM_OPEN=y" >> .config
 			echo "CONFIG_ICE_OPEN=y" >> .config
@@ -286,12 +295,17 @@ function genconfig {
 		fi
 
 		# Force regeneration of themes
-		touch package/feeds/feed_inteno_juci/juci/Makefile
+		touch package/feeds/juci/juci/Makefile
 
 		# Force regeneration of kernel Makefile
 		# Needed to disable kmods for iopsys-brcm targets
 		touch package/kernel/linux/Makefile
 
+		# we need to signal to bradcom SDK that we have changed the board id
+		# currently boardparms.c and boardparms_voice.c is the only place that is depending on inteno boardid name
+		# so just touch that file.
+		[ -d ./build_dir ] && find build_dir/ -name "boardparms*c" -print0 2>/dev/null | xargs -0 touch 2>/dev/null
+				
 		# Set default values based on selected parameters
 		v "$(make defconfig 2>&1)"
 
@@ -330,6 +344,7 @@ function genconfig {
 			-n|--no-update) export IMPORT=0;;
 			-v|--verbose) export VERBOSE="$(($VERBOSE + 1))";;
 			-p|--profile) export PROFILE="$2"; shift;;
+			-r|--repo) export CUSTREPO="$2"; shift;;
 			-s|--override) export SRCTREEOVERR=1;;
 			-h|--help) usage;;
 			-l|--list) list_customers 0 $2;;
@@ -343,6 +358,9 @@ function genconfig {
 			esac
 			shift;
 		done
+
+		CUSTREPO="${CUSTREPO:-git@private.inteno.se:customerconfigs}"
+
 		setup_dirs
 		create_and_copy_files "$1" "$2"
 	fi

iop/scripts/generate_tarballs.sh

@@ -3,15 +3,15 @@
 
 build_bcmkernel_consumer() {
 	local tarfile bcmkernelcommith sdkversion
-    sdkversion=$(grep "CONFIG_BRCM_SDK_VER.*=y" .config | awk -F'[_,=]' '{print$5}')
-	bcmkernelcommith=$(grep -w "PKG_SOURCE_VERSION:" $curdir/feeds/feed_inteno_broadcom/bcmkernel/$sdkversion.mk | cut -d'=' -f2)
+	sdkversion=$(grep "CONFIG_BRCM_SDK_VER.*=y" .config | awk -F'[_,=]' '{print$5}')
+	bcmkernelcommith=$(grep -w "PKG_SOURCE_VERSION:" $curdir/feeds/broadcom/bcmkernel/$sdkversion.mk | cut -d'=' -f2)
 	# do not build bcmopen sdk if it was already built before
-	ssh $SERVER "ls $FPATH/bcmopen-$profile-$bcmkernelcommith.tar.gz" && return
+	ssh $SERVER "ls $FPATH/bcmopen-$board-$bcmkernelcommith.tar.gz" && return
 	cd ./build_dir/target-*_uClibc-0.9.33.*/bcmkernel-3.4-$sdkversion/bcm963xx/release
 	sh do_consumer_release -p $profile -y
 	tarfile='out/bcm963xx_*_consumer.tar.gz'
 	[ $(ls -1 $tarfile |wc -l) -ne 1 ] && echo "Too many tar files: '$tarfile'" && return
-	scp $tarfile $SERVER:$FPATH/bcmopen-$profile-$bcmkernelcommith.tar.gz
+	scp $tarfile $SERVER:$FPATH/bcmopen-$board-$bcmkernelcommith.tar.gz
 	rm -f $tarfile
 	cd $curdir
 }
@@ -20,8 +20,8 @@ build_natalie_consumer() {
 	# create natalie-dect open version tar file
 	local natalieversion nataliecommith
 	grep -q "CONFIG_TARGET_NO_DECT=y" .config && return
-	natalieversion=$(grep -w "PKG_VERSION:" ./feeds/feed_inteno_packages/natalie-dect/Makefile | cut -d'=' -f2)
-	nataliecommith=$(grep -w "PKG_SOURCE_VERSION:" ./feeds/feed_inteno_packages/natalie-dect/Makefile | cut -d'=' -f2)
+	natalieversion=$(grep -w "PKG_VERSION:" ./feeds/iopsys/natalie-dect/Makefile | cut -d'=' -f2)
+	nataliecommith=$(grep -w "PKG_SOURCE_VERSION:" ./feeds/iopsys/natalie-dect/Makefile | cut -d'=' -f2)
 	ssh $SERVER "ls $FPATH/natalie-dect-$profile-$natalieversion-$nataliecommith.tar.gz" && return
 	cd ./build_dir/target-*_uClibc-0.9.33.*/natalie-dect-$natalieversion/
 	mkdir natalie-dect-open-$natalieversion
@@ -38,8 +38,8 @@ build_endptcfg_consumer() {
 	# create endptcfg open version tar file
 	local endptversion endptcommith
 	grep -q "CONFIG_TARGET_NO_VOICE=y" .config && return
-	endptversion=$(grep -w "PKG_VERSION:" ./feeds/feed_inteno_packages/endptcfg/Makefile | cut -d'=' -f2)
-	endptcommith=$(grep -w "PKG_SOURCE_VERSION:" ./feeds/feed_inteno_packages/endptcfg/Makefile | cut -d'=' -f2)
+	endptversion=$(grep -w "PKG_VERSION:" ./feeds/iopsys/endptcfg/Makefile | cut -d'=' -f2)
+	endptcommith=$(grep -w "PKG_SOURCE_VERSION:" ./feeds/iopsys/endptcfg/Makefile | cut -d'=' -f2)
 	ssh $SERVER "ls $FPATH/endptcfg-$profile-$endptversion-$endptcommith.tar.gz" && return
 	cd ./build_dir/target-*_uClibc-0.9.33.*/endptcfg-$endptversion/
 	mkdir endptcfg-open-$endptversion
@@ -55,9 +55,9 @@ build_endptcfg_consumer() {
 build_ice_consumer() {
 	# create ice-client open version tar file
 	local iceversion icebasever icerelease icecommith
-	icecommith=$(grep -w "PKG_SOURCE_VERSION:" ./feeds/feed_inteno_packages/ice-client/Makefile | head -1 | cut -d'=' -f2)
-	icebasever=$(grep -w "BASE_PKG_VERSION:" ./feeds/feed_inteno_packages/ice-client/Makefile | cut -d'=' -f2)
-	icerelease=$(grep -w "PKG_RELEASE:" ./feeds/feed_inteno_packages/ice-client/Makefile | cut -d'=' -f2)
+	icecommith=$(grep -w "PKG_SOURCE_VERSION:" ./feeds/iopsys/ice-client/Makefile | head -1 | cut -d'=' -f2)
+	icebasever=$(grep -w "BASE_PKG_VERSION:" ./feeds/iopsys/ice-client/Makefile | cut -d'=' -f2)
+	icerelease=$(grep -w "PKG_RELEASE:" ./feeds/iopsys/ice-client/Makefile | cut -d'=' -f2)
 	iceversion=$icebasever$icerelease
 	ssh $SERVER "ls $FPATH/ice-client-$target-$iceversion-$icecommith.tar.gz" && return
 	cd ./build_dir/target-*_uClibc-0.9.33.*/ice-client-$icebasever/ipkg-* || cd ./build_dir/target-mips*musl-*/ice-client-$icebasever/ipkg-*
@@ -109,6 +109,7 @@ function generate_tarballs {
     git remote -v | grep -q http && return # do not continue if this is an open SDK environment
 
     target=$(grep CONFIG_TARGET_BOARD .config | cut -d'=' -f2 | tr -d '"')
+    board=$(grep CONFIG_TARGET_IBOARDID .config | cut -d'=' -f2 | tr -d '"')
     profile=$(grep CONFIG_BCM_KERNEL_PROFILE .config | cut -d'=' -f2 | tr -d '"')
     curdir=$(pwd)
 

iop/scripts/ssh_sysupgrade.sh

@@ -34,7 +34,7 @@ function ssh_sysupgrade_latest {
 		exit 1
 	fi
 	{ cd `dirname $0`
-		IMAGE=`ls -Art bin/*/*.y2 | tail -n1`
+		IMAGE=`ls -Art bin/*/*.y[23] | tail -n1`
 		[ "$IMAGE" ] && [ -e "$IMAGE" ] && ./iop ssh_sysupgrade $1 $IMAGE $2
 	}
 }

iop/scripts/update_feed_branches.sh

@@ -0,0 +1,61 @@
+#!/bin/sh
+
+# Exported interface
+function update_feed_branches {
+	local release="$1"
+	local ipath="$(pwd)"
+	local branch="$2"
+	local curbranch
+
+	[ -n "$release" ] || {
+		echo "Usage: ./update_feeds <RELEASE> <BRANCH>"
+		echo ""
+		echo "If you do not give a branch as argument,"
+		echo "<RELEASE> branch will be updated to commit"
+		echo "hash given in feeds.conf for each feed repo"
+		exit 1
+	}
+
+	if [ -n "$branch" ]; then
+		echo "Updating release branch $release to specific commit hash given in feeds.conf for each feed repo at branch $branch"
+		if git diff-index --quiet HEAD; then
+			curbranch=`git symbolic-ref HEAD 2>/dev/null`
+			curbranch=${curbranch##refs/heads/}
+			if [ -z $curbranch ]; then
+				curbranch=`git log -1 --pretty=format:"%H"`
+			fi
+			git checkout $branch || {
+				echo "couldn't checkout branch $branch"
+				exit 99
+			}
+		else
+			echo "You have unsaved changes."
+			exit 99
+		fi
+	else
+		echo "Updating release branch $release to specific commit hash given in feeds.conf for each feed repo"
+	fi
+
+	ifeeds="$(grep -r feed_inteno feeds.conf  | awk '{print$2}' | cut -d'_' -f3 | tr '\n' ' ')"
+
+	for f in $ifeeds; do
+		commith=$(grep feed_inteno_$f feeds.conf | cut -d'^' -f2)
+		cd $ipath/feeds/feed_inteno_$f
+		git branch -D $release 2>/dev/null
+		echo "feed_inteno_$f: updating release branch $release to commit $commith"
+		git checkout $commith
+		git push origin :$release
+		git checkout -b $release
+		git push origin $release
+		cd $ipath
+	done
+
+	if [ -n "$branch" ]; then
+		echo "Release branch $release is updated to specific commit hash given in feeds.conf in in branch $branch for each feed repo"
+		git checkout $curbranch
+	else
+		echo "Release branch $release is updated to specific commit hash given in feeds.conf for each feed repo"
+	fi
+}
+
+register_command "update_feed_branches" "<release> [branch] Update branches in feeds from the current top level commit or specified top level branch"

iop/scripts/update_package.sh

@@ -536,7 +536,7 @@ check_feeds()
 	    read answer
 
 	    case $answer in
-		n|N)
+		n|N|'')
 		    continue;;
 	    esac
 	    branch_uptodate feeds/${feed}

iup/files/sbin/iup

@@ -17,15 +17,27 @@ export IUPTEMP="/tmp/iup"
 export INTERACTIVE=0
 export VERBOSE=0
 export CONF=1
-export DESKEY=$(cat /proc/nvram/DesKey | tr -d '\n' | hexdump -e '16/1 "%02x"')
-export MAC=$(cat /proc/nvram/BaseMacAddr)
+export DESKEY=
+export MAC=
 export RANGE=10
 export RETRYSTOP=5
 export SLEEP=10
-#remove whitespace
-MAC=${MAC// /}
-#lower to upper Conversion
-MAC=$(echo $MAC | tr '[a-z]' '[A-Z]')
+
+local sysinfo=$(ubus call router.system info)
+json_load "$sysinfo"
+json_select system
+json_get_var MAC basemac
+json_select ..
+json_select keys
+json_get_var DESKEY des
+json_select ..
+
+# MAC lowercase to uppercase and remove ':'
+MAC=$(echo $MAC | tr '[a-z]' '[A-Z]' | tr -d ':')
+
+# Convert DESKEY to HEX format
+DESKEY=$(echo $DESKEY | tr -d '\n' | hexdump -e '16/1 "%02x"')
+
 
 # no verbose:	no output
 # -v		log to system log
@@ -183,7 +195,7 @@ handle_Downloaded_file()
 					for f in $CONFILESLURP
 					do
 						v "File to be applied $f and config $(cat $f)"
-						uci import -f $f
+						uci -f $f import
 					done
 					pack=$(get_packages $CONFILESLURP)
 					v "Packages to be commited: $pack"
@@ -446,32 +458,54 @@ parse_dhcp_options()
 # return 1 if the default gateway is not reachable after $wait_time
 wait_for_default_gateway()
 {
-	local gateway
-	local device
+	local gateway device nameservers
 	local wait_time=120
 	local wait_interval=10
+	local interface="$1"
 
 	while [ true ] ; do
 
-		gateway=""
 		device=""
+
 		network_flush_cache
-		network_get_gateway gateway wan #true
-		network_get_device device wan
-		device="${device:+-I }$device"
-		if ping -q -w 1 -c 1 $device $gateway >/dev/null 2>&1 ; then
-			[ "$wait_time" -lt "60" ] && v "Default gateway $gateway is reachable"
-			sleep $wait_interval
-			return 0
+
+		if [ -z "$interface" ]; then
+			network_find_wan interface
 		fi
 
-		v "Waiting for default gateway. Countdown $wait_time seconds"
+		if [ -n "$interface" ]; then
+			network_get_device device $interface
+
+			if [ "$device" ]; then
+				device="${device:+-I }$device"
+				network_get_gateway gateway $interface true
+
+				# ping gateways to check uplink
+				if ping -q -w1 -c 1 $device $gateway >/dev/null 2>&1 ; then
+					[ "$wait_time" -lt "60" ] && v "Default gateway $gateway is reachable"
+					sleep $wait_interval
+					return 0
+				fi
+
+				# try the nameservers too
+				nameservers="$(grep nameserver /var/resolv.conf.auto | awk '{print $2}')"
+				for ns in $nameservers; do
+					if ping -q -w 1 -c 1 $device $ns >/dev/null 2>&1 ; then
+						[ "$wait_time" -lt "60" ] && v "Name server $ns is reachable"
+						sleep $wait_interval
+						return 0
+					fi
+				done
+			fi
+		fi
+
+		v "Waiting for default gateway or name server. Countdown $wait_time seconds"
 		sleep $wait_interval
 		wait_time=$((wait_time - wait_interval))
 		[ "$wait_time" -le "0" ] && break # timer expired
 	done
 
-	return 1 # default gateway not reachable
+	return 1 # default gateway and name server are not reachable
 }
 
 
@@ -496,10 +530,17 @@ main()
 		shift;
 	done
 
-	if ! wait_for_default_gateway ; then
-		v "Default gateway is not reachable. Aborting iup."
+	local interface=""
+
+	config_load provisioning
+	config_get interface polling interface
+
+	if ! wait_for_default_gateway $interface; then
+		v "Neither default gateway nor name server are reachable. Aborting iup."
 		exit 1
 	fi
+	# reload config to get latest values
+	config_load provisioning
 
 	if [ ! -f $IUPMD5 ]; then
 		v "Creating file $IUPMD5"
@@ -512,7 +553,6 @@ main()
 	local software
 	local sofwareminuspath
 
-	config_load provisioning
 	#check if iup should be used or if its overridden by /etc/config
 	config_get configurl configserver	url
 	config_get reboot configserver reboot

layer2interface/broadcom/etc/hotplug.d/switch/10-switch

@@ -0,0 +1,113 @@
+. /lib/network/config.sh
+
+# FIX: for EG300 WAN port for release 3.13.1 - 4.x
+if [ "$INTERFACE" == "eth2" ]; then
+	touch /var/update.eth2
+fi
+# end FIX
+
+addif() {
+	# check if wan had a event and start all related services
+	wan=`uci -q get layer2_interface_ethernet.Wan.baseifname`
+	if [ "$INTERFACE" == "$wan" ]; then
+		/etc/init.d/layer2_interface_ethernet start
+		/etc/init.d/layer2_interface_vlan start
+	fi
+}
+
+delif() {
+	##remove ethernet wan and nuke any vlans associated
+	wan=`uci -q get layer2_interface_ethernet.Wan.baseifname`
+	if [ "$INTERFACE" == "$wan"  ]; then
+		/etc/init.d/layer2_interface_ethernet stop
+	fi
+}
+
+# true if speed on interface is Gbit
+gigatest() {
+	local speed=$(ethctl $INTERFACE media-type 2>&1 | awk '{if (NR == 2) print $6}')
+	case "$speed" in
+		1000*) return 0 ;;
+		*) return 1 ;;
+	esac
+}
+
+# true if there is a link on any lan port
+lan_test () {
+	local landev=$(db get hw.board.ethernetLanPorts)
+	local ledontest
+	for dev in $landev; do
+		ledontest=$(cat /sys/class/net/$dev/operstate)
+		if [ "$ledontest" == "up" ]; then
+			return 0
+		fi
+	done
+	return 1
+}
+
+# true if adsl or vdsl is up.
+dsltest() {
+	if cat /var/state/layer2_interface 2>/dev/null | grep 'adsl\|vdsl' | grep up; then
+		return 0
+	else
+		return 1
+	fi
+}
+
+case "$ACTION" in
+	add|register)
+		case "$PHYSDEVDRIVER" in
+			natsemi) sleep 1 ;;
+		esac
+		addif
+		local interfname=$(interfacename $INTERFACE)
+		local operstate=$(cat /sys/class/net/$INTERFACE/operstate)
+#		if [ "$operstate" == "up" ]; then
+		if true ; then
+			case "$interfname" in
+				GbE*)
+					ubus call led.lan           set '{"state" : "ok"}'
+					ubus call led.gbe           set '{"state" : "ok"}'
+					ubus call led.gbe_phy_link  set '{"state" : "ok"}'
+					ubus call led.gbe_phy_speed set '{"state": "off"}'
+					$(gigatest) && ubus call led.gbe_phy_speed set '{"state":"ok"}'
+				;;
+				LAN*)
+					ubus call led.lan set '{"state":"ok"}'
+				;;
+				WAN*)
+					ubus call led.wan           set '{"state" : "ok"}'
+					ubus call led.wan_phy_link  set '{"state" : "ok"}'
+					ubus call led.wan_phy_speed set '{"state" : "off"}'
+					$(gigatest) && ubus call led.wan_phy_speed set '{"state":"ok"}'
+				;;
+			esac
+		fi		
+	;;
+	remove|unregister)
+		local interfname=$(interfacename $INTERFACE)
+		local operstate=$(cat /sys/class/net/$INTERFACE/operstate)
+		if [ "$operstate" == "down" ]; then
+			case "$interfname" in
+				GbE*)
+					ubus call led.gbe           set '{"state" : "off"}'
+					ubus call led.gbe_phy_link  set '{"state" : "off"}'
+					ubus call led.gbe_phy_speed set '{"state" : "off"}'
+					$(lan_test) || ubus call led.lan set '{"state":"off"}'
+				;;
+				LAN*)
+					$(lan_test) || ubus call led.lan set '{"state":"off"}'
+				;;
+				WAN*)
+					ubus call led.wan           set '{"state" : "off"}'
+					ubus call led.wan_phy_speed set '{"state" : "off"}'
+					ubus call led.wan_phy_link  set '{"state" : "off"}'
+					# is this needed here ?? don't the dsl hotplug event control this ???
+#					$(dsltest) || ubus call led.dsl set '{"state":"off"}'
+				;;
+			esac
+		fi
+		delif
+	;;
+esac
+

layer2interface/broadcom/etc/init.d/layer2_interface

@@ -16,6 +16,7 @@ start_service() {
 	local AnnexL
 	local ADSL2plus
 	local VDSL2
+	local GFast
 	local a8a
 	local b8b
 	local c8c
@@ -23,11 +24,14 @@ start_service() {
 	local a12a
 	local b12b
 	local a17a
+	local a30a
+	local b35b
 	local US0
 	local bitswap
 	local sra
 	local vdsl
 
+
 	config_load layer2_interface
 	config_get Glite capabilities Glite
 	config_get GDmt capabilities GDmt
@@ -36,6 +40,7 @@ start_service() {
 	config_get ADSL2plus capabilities ADSL2plus
 	config_get AnnexL capabilities AnnexL
 	config_get VDSL2 capabilities VDSL2
+	config_get GFast capabilities GFast
 	config_get AnnexM capabilities AnnexM
 
 	config_get a8a capabilities 8a
@@ -45,6 +50,9 @@ start_service() {
 	config_get a12a capabilities 12a
 	config_get b12b capabilities 12b
 	config_get a17a capabilities 17a
+	config_get a30a capabilities 30a
+	config_get b35b capabilities 35b
+	config_get BrcmPriv1 capabilities BrcmPriv1
 
 	config_get US0 capabilities US0
 	config_get bitswap capabilities bitswap
@@ -58,6 +66,7 @@ start_service() {
 	ADSL2plus=$(echo $ADSL2plus | sed 's/Enabled\|1/p/g')
 	AnnexM=$(echo $AnnexM | sed 's/Enabled\|1/m/g')
 	VDSL2=$(echo $VDSL2 | sed 's/Enabled\|1/v/g')
+	GFast=$(echo $GFast | sed 's/Enabled\|1/f/g')
 
 	a8a=$(echo $a8a | sed 's/Enabled\|1/8a/g')
 	b8b=$(echo $b8b | sed 's/Enabled\|1/8b/g')
@@ -66,7 +75,10 @@ start_service() {
 	a12a=$(echo $a12a | sed 's/Enabled\|1/12a/g')
 	b12b=$(echo $b12b | sed 's/Enabled\|1/12b/g')
 	a17a=$(echo $a17a | sed 's/Enabled\|1/17a/g')
-
+	a30a=$(echo $a30a | sed 's/Enabled\|1/30a/g')
+	b35b=$(echo $b35b | sed 's/Enabled\|1/BrcmPriv1/g')
+	BrcmPriv1=$(echo $BrcmPriv1 | sed 's/Enabled\|1/BrcmPriv1/g')
+	[ -n "$b35b" ] && BrcmPriv1=""
 	US0=$(echo $US0 | sed 's/1/on/g')
 	US0=$(echo $US0 | sed 's/0/off/g')
 	bitswap=$(echo $bitswap | sed 's/1/on/g')
@@ -78,18 +90,20 @@ start_service() {
 
 	xtmctl start
 	xtmctl operate intf --state 1 enable
-	json_load "$(ubus call router.system info)"
-	json_select specs
-	json_get_var vdsl vdsl
+	vdsl=$(db get hw.board.hasVdsl)
 
 	if [ $vdsl -eq 1 ]; then
-		echo "xdslctl start --up --mod $GDmt$Glite$T1413$ADSL2$AnnexL$ADSL2plus$AnnexM$VDSL2 --profile \"$a8a $b8b $c8c $d8d $a12a $b12b $a17a\" --sra $sra --bitswap $bitswap --us0 $US0"
-		xdslctl start --up --mod $GDmt$Glite$T1413$ADSL2$AnnexL$ADSL2plus$AnnexM$VDSL2 --profile "$a8a $b8b $c8c $d8d $a12a $b12b $a17a" --sra $sra --bitswap $bitswap --us0 $US0
+		echo "xdslctl start --up --mod $GDmt$Glite$T1413$ADSL2$AnnexL$ADSL2plus$AnnexM$VDSL2$GFast --profile \"$a8a $b8b $c8c $d8d $a12a $b12b $a17a $a30a $b35b $BrcmPriv1\" --sra $sra --bitswap $bitswap --us0 $US0"
+		xdslctl start --up --mod $GDmt$Glite$T1413$ADSL2$AnnexL$ADSL2plus$AnnexM$VDSL2$GFast --profile "$a8a $b8b $c8c $d8d $a12a $b12b $a17a $a30a $b35b $BrcmPriv1" --sra $sra --bitswap $bitswap --us0 $US0
 	else
 		echo "xdslctl start --up --mod $GDmt$Glite$T1413$ADSL2$AnnexL$ADSL2plus$AnnexM --sra $sra --bitswap $bitswap"
 		xdslctl start --up --mod $GDmt$Glite$T1413$ADSL2$AnnexL$ADSL2plus$AnnexM --sra $sra --bitswap $bitswap
 	fi
 
+	if [ "$GFast" == "f" ]; then
+		# enable V43 tone set for GFAST
+		xdslctl configure1 --phycfg 0 0 0 0 0 0 0 0 0 0 0 0x400000 0x400000
+	fi
 }
 
 

layer2interface/broadcom/etc/init.d/layer2_interface_ethernet

@@ -55,7 +55,6 @@ addethernet() {
 	ifname="${ifname:-$baseifname.1}"
 
 	brcm_virtual_interface_rules "$baseifname" "$ifname" "$bridge" "$mac2"
-
 }
 
 boot() {
@@ -96,12 +95,15 @@ start_service() {
 	echo "Setting up Ethernet WAN"
 	config_load layer2_interface_ethernet
 	config_foreach addethernet ethernet_interface
+	/etc/init.d/layer2_interface_vlan start
 }
 
 stop_service() {
 	local ifname
 	config_load layer2_interface_ethernet
 	config_foreach removeethernet ethernet_interface
+	/etc/init.d/layer2_interface_vlan stop
+	sleep 1
 }
 
 reload_service() {
@@ -113,4 +115,3 @@ service_triggers() {
 	procd_add_reload_trigger layer2_interface_ethernet
 }
 
-

layer2interface/broadcom/etc/uci-defaults/20-layer2-config-generate

@@ -1,30 +1,13 @@
 #!/bin/sh
 
-local hasEthWan="1"
+local hasEthWan="$(db -q get hw.board.hasEthWan)"
+hasEthWan=${hasEthWan:-1}
 local hasAdsl="$(db -q get hw.board.hasAdsl)"
 local hasVdsl="$(db -q get hw.board.hasVdsl)"
 
 local LANPORTS="$(db -q get hw.board.ethernetLanPorts)"
 local WANPORTS=""
 
-# populate layer2_interface_ethernet #
-if [ "$hasEthWan" == "1" ]; then
-	local wanEthernetPort="$(db -q get hw.board.ethernetWanPort)"
-	wanEthernetPort="${wanEthernetPort:-eth0}"
-	if [ ! -f /etc/config/layer2_interface_ethernet -o -z "$(uci -q get layer2_interface_ethernet.@ethernet_interface[0].ifname)" ]; then
-		cat > /etc/config/layer2_interface_ethernet <<EOF
-config ethernet_interface 'Wan'
-	option name 'WAN'
-	option baseifname '${wanEthernetPort}'
-	option ifname '${wanEthernetPort}.1'
-EOF
-	fi
-	local ifname="$(uci -q get layer2_interface_ethernet.@ethernet_interface[0].ifname)"
-	[ -n "$WANPORTS" ] && WANPORTS="$WANPORTS $ifname" || WANPORTS="$ifname"
-elif [ "$hasEthWan" == "0" ]; then
-	echo "" > /etc/config/layer2_interface_ethernet
-fi
-
 # populate layer2_interface #
 if [ "$hasAdsl" == "1" ]; then
 	if [ ! -f /etc/config/layer2_interface -o -z "$(uci -q get layer2_interface.capabilities)" ]; then
@@ -60,6 +43,28 @@ elif [ "$hasAdsl" == "0" -a "$hasVdsl" == "0" ]; then
 	echo "" > /etc/config/layer2_interface
 fi
 
+# populate layer2_interface_vdsl #
+if [ "$hasVdsl" == "1" ]; then
+	local wanVdslPort=$(db -q get hw.board.vdslWanPort)
+	wanVdslPort="${wanVdslPort:-ptm0}"
+	if [ ! -f /etc/config/layer2_interface_vdsl -o -z "$(uci -q get layer2_interface_vdsl.@vdsl_interface[0].ifname)" ]; then
+		cat > /etc/config/layer2_interface_vdsl <<EOF
+config vdsl_interface
+	option 'unit' '0'
+	option 'ifname' '${wanVdslPort}.1'
+	option 'baseifname' '${wanVdslPort}'
+	option 'name' 'VDSL2'
+	option 'dslat' '1'
+	option 'ptmprio' '1'
+	option 'ipqos' '1'
+EOF
+	fi
+	local ifname="$(uci -q get layer2_interface_vdsl.@vdsl_interface[0].ifname)"
+	[ -n "$WANPORTS" ] && WANPORTS="$WANPORTS $ifname" || WANPORTS="$ifname"
+elif [ "$hasVdsl" == "0" ]; then
+	echo "" > /etc/config/layer2_interface_vdsl
+fi
+
 # populate layer2_interface_adsl #
 if [ "$hasAdsl" == "1" ]; then
 	local wanAdslPort=$(db -q get hw.board.adslWanPort)
@@ -84,26 +89,22 @@ elif [ "$hasAdsl" == "0" ]; then
 	echo "" > /etc/config/layer2_interface_adsl
 fi
 
-# populate layer2_interface_vdsl #
-if [ "$hasVdsl" == "1" ]; then
-	local wanVdslPort=$(db -q get hw.board.vdslWanPort)
-	wanVdslPort="${wanVdslPort:-ptm0}"
-	if [ ! -f /etc/config/layer2_interface_vdsl -o -z "$(uci -q get layer2_interface_vdsl.@vdsl_interface[0].ifname)" ]; then
-		cat > /etc/config/layer2_interface_vdsl <<EOF
-config vdsl_interface
-	option 'unit' '0'
-	option 'ifname' '${wanVdslPort}.1'
-	option 'baseifname' '${wanVdslPort}'
-	option 'name' 'VDSL2'
-	option 'dslat' '1'
-	option 'ptmprio' '1'
-	option 'ipqos' '1'
+# populate layer2_interface_ethernet #
+if [ "$hasEthWan" == "1" ]; then
+	local wanEthernetPort="$(db -q get hw.board.ethernetWanPort)"
+	wanEthernetPort="${wanEthernetPort:-eth0}"
+	if [ ! -f /etc/config/layer2_interface_ethernet -o -z "$(uci -q get layer2_interface_ethernet.@ethernet_interface[0].ifname)" ]; then
+		cat > /etc/config/layer2_interface_ethernet <<EOF
+config ethernet_interface 'Wan'
+	option name 'WAN'
+	option baseifname '${wanEthernetPort}'
+	option ifname '${wanEthernetPort}.1'
 EOF
 	fi
-	local ifname="$(uci -q get layer2_interface_vdsl.@vdsl_interface[0].ifname)"
+	local ifname="$(uci -q get layer2_interface_ethernet.@ethernet_interface[0].ifname)"
 	[ -n "$WANPORTS" ] && WANPORTS="$WANPORTS $ifname" || WANPORTS="$ifname"
-elif [ "$hasVdsl" == "0" ]; then
-	echo "" > /etc/config/layer2_interface_vdsl
+elif [ "$hasEthWan" == "0" ]; then
+	echo "" > /etc/config/layer2_interface_ethernet
 fi
 
 # populate network config ifnames #

layer2interface/broadcom/lib/network/brcmwifi.sh

@@ -91,12 +91,13 @@ wlmngr_doWlConf() {
 wlmngr_setupMbssMacAddr() {
 	local idx=$1
 	local hwaddr
-
+	wlmngr_WlConfDown $idx
 	for vif in $(nvram get "wl$idx"_vifs); do
 		hwaddr=$(nvram get "$vif"_hwaddr)
 		ifconfig $vif hw ether $hwaddr 2>/dev/null
 		wlctl -i $vif cur_etheraddr $hwaddr 2>/dev/null
 	done
+	wlmngr_doWlConf $idx
 }
 
 #enableSSD() {
@@ -200,14 +201,14 @@ enableBSD() {
 					nvram set ${wdev}_bsd_if_select_policy=$wdev_to_steer
 					nvram set ${wdev}_bsd_sta_select_policy="20 -60 0 0 1 0 0 0 0 0x42"
 					nvram set ${wdev}_bsd_steer_prefix=$wdev
-					nvram set ${wdev}_bsd_steering_policy="0 0 0 -60 0 0x52"
+					nvram set ${wdev}_bsd_steering_policy="0 0 0 -60 0 0x0"
 				else
 					# 5G
 					nvram set ${wdev}_bsd_if_qualify_policy="30 0x0"
 					nvram set ${wdev}_bsd_if_select_policy=$wdev_to_steer
 					nvram set ${wdev}_bsd_sta_select_policy="20 $rssi_threshold 0 0 1 0 0 0 0 0x40"
 					nvram set ${wdev}_bsd_steer_prefix=$wdev
-					nvram set ${wdev}_bsd_steering_policy="80 5 3 $rssi_threshold 0 0x40"
+					nvram set ${wdev}_bsd_steering_policy="80 5 3 $rssi_threshold 0 0x0"
 				fi
 			else
 				# Bandwidth Usage based policy #
@@ -261,6 +262,7 @@ wlmngr_startWsc()
 	nvram set wps_timeout_enable=0
 	#nvram get wps_config_method
 	nvram set wps_version2=enabled # extra
+	nvram set wps_oob_configured=1
 	nvram set lan_wps_oob=disabled # extra
 	nvram set lan_wps_reg=enabled # extra
 
@@ -347,6 +349,9 @@ wlmngr_doQoS() {
 
 wlmngr_finalize() {
 	local idx=$1
+	local dconpoll="$(uci -q get wireless.wl$idx.dconpoll)"
+
+	dconpoll=${dconpoll:-0}
 
 	wlctl -i wl$idx phy_watchdog 1
 	wlctl -i wl$idx fcache 1
@@ -355,8 +360,8 @@ wlmngr_finalize() {
 	local pcid="$(wlctl -i wl$idx revinfo | awk 'FNR == 2 {print}' | cut -d'x' -f2)"
 	local isac="$(db get hw.$pcid.is_ac)"
 	if [ "$isac" == "1" ]; then
-		wlctl -i wl$idx msglevel +radar +dfs 2>/dev/null
-		dhdctl -i wl$idx dconpoll 200 2>/dev/null
+		#wlctl -i wl$idx msglevel +dfs 2>/dev/null
+		dhdctl -i wl$idx dconpoll $dconpoll 2>/dev/null
 	fi
 	local rdrthrs="$(db get hw.$pcid.radarthrs)"
 	if [ -n "$rdrthrs" ]; then
@@ -367,6 +372,19 @@ wlmngr_finalize() {
 	# this piece of code is -required- to make br-lan's mac work properly
 	# in all cases
 	sendarp -s br-lan -d br-lan
+
+	# set power percent
+	local pwrpercent="$(uci -q get wireless.wl$idx.txpower)"
+	pwrpercent=${pwrpercent:-100}
+	wlctl -i wl$idx pwr_percent $pwrpercent
+
+	# set message level
+	wlctl -i wl$idx msglevel 0x0 2>/dev/null
+	dhdctl -i wl$idx msglevel 0x0 2>/dev/null
+	for msg in $(uci -q get wireless.wl$idx.msglevel); do
+		wlctl -i wl$idx msglevel +$msg 2>/dev/null
+		dhdctl -i wl$idx msglevel +$msg 2>/dev/null
+	done
 }
 
 wlmngr_issueServiceCmd() {

layer2interface/broadcom/lib/network/vlan.sh

@@ -58,17 +58,45 @@ ifbaseexists()
 	return 0
 }
 
+get_bridge_of() {
+
+        find_network() {
+                local config="$1"
+                local iface="$2"
+                local net=
+                local if_type
+                ifname="$(uci get network.$config.ifname)"
+                if_type="$(uci get network.$config.type)"
+                [ "$if_type" == "bridge" ] || return
+                for ifc in $ifname; do
+                        if [ "$ifc" == "$iface" ]; then
+                                net=$config
+                                break
+                        fi
+                done
+                [ -n "$net" ] && echo $net
+        }
+
+        config_load network
+        config_foreach find_network interface $1
+}
+
 check_mac_address()
 {
-	local baseifname="$1"
-	local vlan="$2"
-	local basemac
-	local mac=$(ifconfig -a | grep "^${baseifname}.${vlan} " | awk '{print $NF}')
-	local mac_in_use=$(ifconfig -a | grep "$mac" | grep -v "^${baseifname}.${vlan}[ ]")
-	if [ "$mac_in_use" ]; then
-		basemac=$(ifconfig -a | grep "^$baseifname " | awk '{print $NF}')
-		ifconfig ${baseifname}.${vlan} hw ether $basemac
-	fi
+        local baseifname="$1"
+        local vlan="$2"
+        local basemac
+        local mac=$(ifconfig -a | grep "^${baseifname}.${vlan} " | awk '{print $NF}')
+        local br_name=$(get_bridge_of ${baseifname}.${vlan})
+        if [ -n "$br_name" ];then
+                local mac_in_use=$(ifconfig -a | grep "$mac" | grep -v "^${baseifname}.${vlan}[ ]" | grep -v "$br_name")
+        else
+                local mac_in_use=$(ifconfig -a | grep "$mac" | grep -v "^${baseifname}.${vlan}[ ]")
+        fi
+        if [ "$mac_in_use" ]; then
+                basemac=$(ifconfig -a | grep "^$baseifname " | awk '{print $NF}')
+                ifconfig ${baseifname}.${vlan} hw ether $basemac
+        fi
 }
 
 addbrcmvlan()

loop-detector/Makefile

@@ -0,0 +1,48 @@
+include $(TOPDIR)/rules.mk
+
+PKG_NAME:=loop-detector
+PKG_VERSION:=1.0
+
+PKG_SOURCE_VERSION:=d0fb770eacd6691b98df138b60f5116e02f71a9b
+PKG_SOURCE_PROTO:=git
+PKG_SOURCE_URL:=https://dev.iopsys.eu/iopsys/loop-detector
+
+PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz
+PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
+PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)-$(PKG_VERSION)
+
+include $(INCLUDE_DIR)/package.mk
+
+
+define Package/loop-detector
+  SECTION:=utils
+  CATEGORY:=Utilities
+  TITLE:=L2 Loop detector
+  DEPENDS:= +libpcap +libuci +libpthread
+endef
+
+define Package/loop-detector/description
+	L2 Loop detection package
+endef
+
+TARGET_CFLAGS += \
+	-D_GNU_SOURCE
+
+TARGET_LDFLAGS += \
+	-Wl,-rpath-link=$(STAGING_DIR)/usr/lib
+
+CONFIGURE_ARGS += \
+	--with-uci-include-path=$(STAGING_DIR)/usr/include \
+	--with-libubox-include-path=$(STAGING_DIR)/usr/include \
+	--with-libubus-include-path=$(STAGING_DIR)/usr/include
+
+define Package/loop-detector/install
+	$(INSTALL_DIR) $(1)/sbin
+	$(INSTALL_BIN) $(PKG_BUILD_DIR)/loop-detector $(1)/sbin/
+	$(INSTALL_DIR) $(1)/etc/init.d
+	$(CP) ./files/loop_detection.init $(1)/etc/init.d/loop_detection
+	$(INSTALL_DIR) $(1)/etc/config
+	$(CP) ./files/loop_detection.config $(1)/etc/config/loop_detection
+endef
+
+$(eval $(call BuildPackage,loop-detector))

loop-detector/files/loop_detection.config

@@ -0,0 +1,5 @@
+config loop-detect loop
+	option enabled '1'
+	option discovery_interval '10'
+	option recovery_check_tries '5'
+

loop-detector/files/loop_detection.init

@@ -0,0 +1,36 @@
+#!/bin/sh /etc/rc.common
+
+START=21
+STOP=89
+
+USE_PROCD=1
+NAME=loop-detector
+
+start_service() {
+	local enabled
+
+	config_load loop_detection
+	config_get_bool enabled loop enabled 1
+
+	if [ $enabled -eq 1 ]; then
+		procd_open_instance
+		procd_set_param command "/sbin/loop-detector"
+		procd_set_param respawn
+		procd_close_instance
+	fi
+}
+
+stop() {
+	service_stop /sbin/loop-detector
+}
+
+service_triggers()
+{
+	procd_add_reload_trigger loop_detection
+}
+
+reload_service() {
+	stop
+	start
+}
+

mtk-bndstrg/Makefile

@@ -1,41 +0,0 @@
-include $(TOPDIR)/rules.mk
-include $(INCLUDE_DIR)/kernel.mk
-
-PKG_NAME:=mtk-bndstrg
-PKG_VERSION:=1.0
-PKG_RELEASE:=1
-
-PKG_SOURCE_VERSION:=8a804320c53dead1c9b9f3650cbbc58908c76832
-PKG_SOURCE_PROTO:=git
-PKG_SOURCE_URL:=http://public.inteno.se:/mtk-bndstrg
-
-PKG_SOURCE:=$(PKG_NAME).tar.gz
-PKG_SOURCE_SUBDIR:=$(PKG_NAME)
-PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)
-
-include $(INCLUDE_DIR)/package.mk
-
-define Package/mtk-bndstrg
-  SECTION:=utils
-  CATEGORY:=Utilities
-  DEPENDS:=+libpthread +librt
-  TITLE:=Band steering daemon for Mediatek
-endef
-
-define Package/mtk-bndstrg/description
- Band steering for Mediatek
-endef
-
-#define Build/Compile
-#endef
-
-define Build/Configure
-  #$(call Build/Configure/Default,--with-linux-headers=$(LINUX_DIR))
-endef
-
-define Package/mtk-bndstrg/install
-	$(INSTALL_DIR) $(1)/usr/sbin
-	$(INSTALL_BIN) $(PKG_BUILD_DIR)/bndstrg $(1)/usr/sbin/
-endef
-
-$(eval $(call BuildPackage,mtk-bndstrg))

natalie-dect-h/Makefile

@@ -11,7 +11,7 @@ PKG_NAME:=natalie-dect-h
 PKG_VERSION:=12.26
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz
-PKG_SOURCE_URL:=http://public.inteno.se:/natalie-dect-h
+PKG_SOURCE_URL:=https://dev.iopsys.eu/dialog/natalie-dect-h.git
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_VERSION:=9e2236989ff58d0db897f938b6b07b535144e0e2
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)

natalie-dect/Makefile

@@ -18,11 +18,12 @@ PKG_SOURCE_URL:=http://iopsys.inteno.se/iopsys/consumer/
 PKG_NAME:=natalie-dect-open
 else
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz
-PKG_SOURCE_URL:=git@private.inteno.se:natalie-dect-12.26
+PKG_SOURCE_URL:=git@dev.iopsys.eu:dialog/natalie-dect-12.26
 PKG_SOURCE_PROTO:=git
 endif
 
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
+PKG_BUILD_PARALLEL:=0
 
 include $(INCLUDE_DIR)/package.mk
 include $(INCLUDE_DIR)/image.mk

peripheral_manager/Makefile

@@ -12,9 +12,9 @@ PKG_NAME:=peripheral_manager
 PKG_VERSION:=1.0.0
 PKG_RELEASE:=1
 
-PKG_SOURCE_VERSION:=ff2cf8bfbd3a04731088e9f4540796696e961382
+PKG_SOURCE_VERSION:=959eca8ab2b50eaccfff9c710cffe5b317bb6ad1
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_URL:=http://public.inteno.se/peripheral_manager
+PKG_SOURCE_URL:=https://dev.iopsys.eu/iopsys/peripheral-manager
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_RELEASE)-$(PKG_SOURCE_VERSION).tar.gz
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)

port-management/files/etc/init.d/port_management

@@ -62,18 +62,25 @@ get_current_status() {
 	fi
 }
 
-sfp_flag(){
+get_flag(){
 	local port=$1
 	local sfptype=$2
-	local media="$(ethctl $port media-type 2>&1 | grep 'This is probably wrong')"
-	[ -z "$media" ] && echo "" || echo "sfp $sfptype"
+	local eg300="$(ethctl $port media-type 2>&1 | grep 'This is probably wrong')"
+	local eg400="$(ethctl $port media-type 2>&1 | grep 'Error: Interface eth0 has sub ports, please specified one')"
+	if [ -n "$eg300" ]; then
+		echo "sfp copper"
+	elif [ -n "$eg400" ]; then
+		echo "port 10"
+	else
+		echo ""
+	fi
 }
 
 set_port_status() {
 	local port="$1"
 	local status="$2"
-	local flag=$(sfp_flag $port "copper")
-	local curstatus=$(get_current_status $port $flag)
+	local flag=$(get_flag $port)
+	local curstatus=$(get_current_status "$port" "$flag")
 
 	ifconfig $port >/dev/null 2>&1 || return
 
@@ -93,14 +100,14 @@ set_port_status() {
 						esac
 					;;
 					10*AUTO)
-						ethctl $port media-type $flag advertise $status
+						ethctl $port media-type advertise $status $flag
 					;;
 					10*)
-						ethctl $port media-type $flag $status
+						ethctl $port media-type $status $flag
 					;;
 					*)
-						ethctl $port media-type $flag advertise 1000FDAUTO
-						ethctl $port media-type $flag auto
+						ethctl $port media-type advertise 1000FDAUTO $flag
+						ethctl $port media-type auto $flag
 					;;
 				esac
 			else

port-management/files/etc/init.d/sfp_management

@@ -23,18 +23,24 @@ get_current_status() {
 	fi
 }
 
-sfp_flag(){
+get_flag(){
 	local port=$1
-	local sfptype=$2
-	local media="$(ethctl $port media-type 2>&1 | grep 'This is probably wrong')"
-	[ -z "$media" ] && echo "" || echo "sfp $sfptype"
+	local eg300="$(ethctl $port media-type 2>&1 | grep 'This is probably wrong')"
+	local eg400="$(ethctl $port media-type 2>&1 | grep 'Error: Interface eth0 has sub ports, please specified one')"
+	if [ -n "$eg300" ]; then
+		echo "sfp fiber"
+	elif [ -n "$eg400" ]; then
+		echo "port 9"
+	else
+		echo ""
+	fi
 }
 
 set_fiber_status() {
 	local port="$1"
 	local status="$2"
-	local flag=$(sfp_flag $port "fiber")
-	local curstatus=$(get_current_status $port $flag)
+	local flag=$(get_flag $port)
+	local curstatus=$(get_current_status "$port" "$flag")
 
 	case "$status" in
 		disabled)

questd/Makefile

@@ -6,11 +6,11 @@ include $(TOPDIR)/rules.mk
 include $(INCLUDE_DIR)/kernel.mk
 
 PKG_NAME:=questd
-PKG_VERSION:=3.1.38
+PKG_VERSION:=3.1.40
 
-PKG_SOURCE_VERSION:=4e1e080fb8295d89c74abb93e08dcf2f9cc5abbf
+PKG_SOURCE_VERSION:=947315714433ac9a4faf8e39f9ab285964a553d1
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_URL:=http://public.inteno.se:/questd
+PKG_SOURCE_URL:=https://dev.iopsys.eu/iopsys/questd
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
@@ -43,7 +43,7 @@ export QUESTD_CFLAGS
 
 define Package/questd
 	CATEGORY:=Utilities
-	DEPENDS:=+libuci +libubox +ubus +libpthread +(TARGET_iopsys_ramips_ex400):swconfig +(TARGET_iopsys_ramips_ex400):libnl-tiny
+	DEPENDS:=+libuci +libubox +ubus +libpthread +(TARGET_iopsys_ramips_ex400):swconfig +(TARGET_iopsys_ramips_ex400):libnl-tiny +libopenssl
 	TITLE:=router info daemon
 endef
 

questd/files/etc/init.d/quest

@@ -20,11 +20,6 @@ start_service() {
 	pidof imonitor > /dev/null 2>&1 || /sbin/imonitor &
 }
 
-stop() {
-	service_stop /sbin/questd
-	service_stop /sbin/graphd
-}
-
 service_triggers()
 {
 	procd_add_reload_trigger network wireless
@@ -34,3 +29,12 @@ reload_service() {
 	ubus -t 5 call router.network reload
 }
 
+print_out_data() {
+	logger -t "environment" "Software Version: $(grep 'IOP Version' /etc/banner | awk '{print$3}')"
+	[ -s /etc/boot_reason ] && logger -t "environment" "Boot Reason: $(cat /etc/boot_reason)"
+}
+
+boot() {
+	print_out_data
+	start_service
+}

questd/files/sbin/imonitor

@@ -1,6 +1,7 @@
 #!/bin/sh
 
 . /lib/functions.sh
+. /usr/share/libubox/jshn.sh
 
 # 1. sleep for $SLEEP_LONG seconds
 # 2. run the check_* functions
@@ -22,7 +23,7 @@ NPROC_COUNT=4	# number of time that the NPROC_LIMIT has to be hit to trigger a p
 NPROC_NFAIL=0	# current consecutive Number of FAILures. process restarts when NPROC_NFAIL == NPROC_COUNT
 
 # memmory limit
-MEM_LIMIT=50000
+MEM_LIMIT=20000
 MEM_COUNT=4
 MEM_NFAIL=0
 
@@ -31,27 +32,37 @@ PCPU_LIMIT=38
 PCPU_COUNT=4
 PCPU_NFAIL=0
 
+# network call check
+NNET_NFAIL=0
+
 UBUS_TIMEOUT=5
 
 
 BSDBIN=$(which bsd)
 ACSDBIN=$(which acsd)
 
+RESTART_ACSD=0
+RESTART_BSD=0
+
+DUALBAND=1
+
 restart_questd()
 {
-	logger -s -t $0[$$] "Restarting questd. $NPROC_NFAIL $MEM_NFAIL $PCPU_NFAIL"
+	logger -s -t $0[$$] "Restarting questd. $NPROC_NFAIL $MEM_NFAIL $PCPU_NFAIL $NNET_NFAIL"
 
-	killall -q -KILL questd
 	/etc/init.d/quest stop
 	killall -q -KILL questd
+	killall -q -KILL questd
 	/etc/init.d/quest start
 
+	sleep 5
+
 	NPROC_NFAIL=0
 	MEM_NFAIL=0
 	PCPU_NFAIL=0
+	NNET_NFAIL=0
 }
 
-
 check_nproc()
 {
 	local nproc="$@"
@@ -110,21 +121,52 @@ check_pcpu()
 
 check_ubuscall()
 {
-	local rv
+		local rv
 
-	ubus -t $UBUS_TIMEOUT call router.system info >/dev/null 2>&1
-	rv=$?
+		ubus -t $UBUS_TIMEOUT call router.system info >/dev/null 2>&1
+		rv=$?
 
-	[ "$rv" = "0" ] && return 0
-	return 1
+		[ "$rv" = "0" ] && return 0
+		return 1
 }
 
+check_ubus_network_call() {
+	[ "$(uci -q get network.lan)" == "interface" ] || return 0
+	json_load "$(ifstatus lan)" || return 0
+	json_get_var up up
+	[ $up -eq 1 ] || return 0
+	local ifname="$(uci -q get network.lan.ifname)"
+	[ -z "$ifname" -o "${ifname:0:3}" == "br-" ] && return 0
+	ubus -t 5 call router.network ports '{"network":"lan"}' | grep -q statistics || {
+		NNET_NFAIL=1
+		return 1
+	}
+	return 0
+}
 
 restart_bsd()
 {
-	logger -s -t $0[$$] "Restarting bsd."
-	killall -q -KILL bsd
-	bsd
+	killall -q -15 bsd 2>/dev/null
+
+	[ "$(nvram get wl0_radio)" == "1" -a "$(nvram get wl1_radio)" == "1" ] || {
+		[ $DUALBAND -eq 1 ] && logger -s -t $0[$$] "Band Steering is deactivated; will be re-activated when both 2.4GHz and 5GHz radios are enabled."
+		DUALBAND=0
+		return 0
+	} && DUALBAND=1
+
+	logger -s -t $0[$$] "Restarting Band Steering daemon due to bsd hangup."
+
+	if [ $RESTART_BSD -eq 3 ]; then
+		wlctl -i wl0 down 2>/dev/null
+		wlctl -i wl1 down 2>/dev/null
+		wlctl -i wl0 up 2>/dev/null
+		wlctl -i wl1 up 2>/dev/null
+		RESTART_ACSD=0
+		RESTART_BSD=0
+	else
+		RESTART_BSD=$((RESTART_BSD+1))
+	fi
+	bsd &
 }
 
 check_bsdcall()
@@ -141,9 +183,19 @@ check_bsdcall()
 
 restart_acsd()
 {
-	logger -s -t $0[$$] "Restarting acsd."
-	killall -q -KILL acsd
-	acsd &
+	logger -s -t $0[$$] "Restarting Auto Channel Selection daemon due to acsd high CPU usage."
+	killall -q -9 acsd 2>/dev/null
+	if [ $RESTART_ACSD -eq 3 ]; then
+		wlctl -i wl0 down 2>/dev/null
+		wlctl -i wl1 down 2>/dev/null
+		wlctl -i wl0 up 2>/dev/null
+		wlctl -i wl1 up 2>/dev/null
+		RESTART_ACSD=0
+		RESTART_BSD=0
+	else
+		RESTART_ACSD=$((RESTART_ACSD+1))
+	fi
+	acsd
 }
 
 check_acsd()
@@ -155,7 +207,7 @@ check_acsd()
 
 	for p in $pcpu; do
 		p=${p%%%*}
-		if [ "$p" -ge "20" ]; then
+		if [ "$p" -ge "40" ]; then
 			return 1
 		fi
 	done
@@ -193,21 +245,23 @@ main()
 			"$restart_mem"   = "1" -o \
 			"$restart_pcpu"  = "1" ]
 		then
-			# check_ubuscall || restart_questd
 			restart_questd
+#		else
+#			if [ "$sample" -ge "$SAMPLES" ]; then
+#				check_ubus_network_call || restart_questd
+#			fi
 		fi
 
-		if [ "$BSDBIN" ] ; then
-			config_load wireless
-			config_get_bool bsdenabled bandsteering enabled 0
-			if [ $bsdenabled == "1" -a "$(pidof wifi)" == "" ] ; then
-				check_bsdcall || restart_bsd
-			fi
-		fi
+#		if [ "$BSDBIN" ] ; then
+#			bsdenabled="$(uci -q get wireless.bandsteering.enabled)"
+#			if [ $bsdenabled == "1" -a "$(pidof wifi)" == "" ] ; then
+#				check_bsdcall || restart_bsd
+#			fi
+#		fi
 
-		if [ "$ACSDBIN" ] ; then
-			check_acsd || restart_acsd
-		fi
+#		if [ "$ACSDBIN" ] ; then
+#			check_acsd || restart_acsd
+#		fi
 
 		# sleep
 		if [ "$sample" -lt "$SAMPLES" ]; then

samba2/Makefile

@@ -8,10 +8,10 @@
 include $(TOPDIR)/rules.mk
 
 PKG_NAME:=samba2
-PKG_VERSION:=2.2.12.inteno
+PKG_VERSION:=2.2.12
 PKG_RELEASE:=1
 
-PKG_SOURCE_URL:=http://public.inteno.se:/samba2
+PKG_SOURCE_URL:=https://dev.iopsys.eu/fork/samba2.git
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_VERSION:=d687d07a137981f4fe78cc289b040e6426c61e29
 PKG_BUILD_DIR=$(BUILD_DIR)/$(PKG_NAME)-$(PKG_VERSION)
@@ -55,11 +55,14 @@ define Package/samba2-client
 endef
 
 TARGET_CFLAGS += $(FPIC)
+WERR := -Werror=format-security
+TARGET_CFLAGS_WITHOUT_WERR := $(filter-out $(WERR),$(TARGET_CFLAGS))
 
 define Build/Compile	
 	rm -rf $(PKG_INSTALL_DIR)
 	mkdir -p $(PKG_INSTALL_DIR)
 	(cd $(PKG_BUILD_DIR)/source ; rm -rf config.{cache,status} ; \
+		CFLAGS="-D_LARGEFILE64_SOURCE -D_GNU_SOURCE" \
 		./configure \
 			$(HOST_CONFIGURE_VARS) \
 			$(HOST_CONFIGURE_ARGS) \
@@ -93,7 +96,7 @@ define Build/Compile
 		clean
 	(cd $(PKG_BUILD_DIR)/source; rm -rf config.{cache,status}; \
 		$(TARGET_CONFIGURE_OPTS) \
-		CFLAGS="$(TARGET_CFLAGS) -D_GNU_SOURCE -DNDEBUG -DSHMEM_SIZE=524288 -Dfcntl=fcntl64" \
+		CFLAGS="$(TARGET_CFLAGS_WITHOUT_WERR) -D_GNU_SOURCE -DNDEBUG -DSHMEM_SIZE=524288" \
 		CPPFLAGS="$(TARGET_CPPFLAGS)" \
 		LDFLAGS="$(TARGET_LDFLAGS) $(LIBGCC_S)" \
 		ac_cv_lib_cups_httpConnect=no \

samba3/files/samba.init

@@ -11,6 +11,11 @@ useradd()
 	local password
 	config_get user $1 user
 	config_get password $1 password
+
+	filter="0A;5C 6E"
+	[ "$(hex_filter "$user" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$password" "$filter" 1)" = "" ] || return
+
 	if ! $(grep -rq "^$user:" /etc/passwd) ; then
 		echo "adding user $user"
 		adduser $user -s /bin/false -D -H -h /mnt/$user -g "samba,pass=$password" && smbpasswd $user $password
@@ -51,6 +56,29 @@ purgepasswd()
 	done
 }
 
+hex_filter() {
+	local string=$1
+	local hex_chars=$2
+	local wc_max=$3
+	local wc_tot=0
+
+	if [ -z "$string" -o -z "$hex_chars" -o -z "$wc_max" ]
+		then
+		return;
+	fi
+
+	dump=$(echo "$string" | hexdump -v -e '32/1 "%02X ""\n"')
+
+	IFS=';'
+	for i in $hex_chars; do
+		local wc
+		wc=$(echo "$dump" | grep -o "$i" | wc -w)
+		wc_tot=$((wc_tot+wc))
+	done
+
+	[ $wc_tot -gt $wc_max ] && echo "corrupt"
+}
+
 smb_header() {
 	local interface
 	config_get interface $1 interface
@@ -80,6 +108,14 @@ smb_header() {
 	config_get description $1 description "Samba on ${hostname:-OpenWrt}"
 	config_get charset     $1 charset     "UTF-8"
 
+	filter="0A;5C 6E"
+	[ "$(hex_filter "$name" "$filter" 1)" = "" ] || exit
+	[ "$(hex_filter "$workgroup" "$filter" 1)" = "" ] || exit
+	[ "$(hex_filter "$description" "$filter" 1)" = "" ] || exit
+	[ "$(hex_filter "$interfaces" "$filter" 1)" = "" ] || exit
+	[ "$(hex_filter "$charset" "$filter" 1)" = "" ] || exit
+
+
 	mkdir -p /var/etc
 	sed -e "s#|NAME|#$name#g" \
 	    -e "s#|WORKGROUP|#$workgroup#g" \
@@ -138,6 +174,15 @@ smb_add_share() {
 	path=$(readlink -f $path)
 	[ "${path:0:4}" == "/mnt" ] || path="/mnt/"
 
+	filter="0A;5C 6E"
+	[ "$(hex_filter "$name" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$users" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$read_only" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$guest_ok" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$create_mask" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$dir_mask" "$filter" 1)" = "" ] || return
+	[ "$(hex_filter "$browseable" "$filter" 1)" = "" ] || return
+
 	echo -e "\n[$name]\n\tpath = $path" >> /var/etc/smb.conf
 	[ -n "$users" ] && echo -e "\tvalid users = $users" >> /var/etc/smb.conf
 	[ -n "$read_only" ] && echo -e "\tread only = $read_only" >> /var/etc/smb.conf

samba3/patches/520-fix_samba3_compilation_error

@@ -0,0 +1,40 @@
+--- a/source/utils/owrt_smbpasswd.c	2017-10-03 15:57:24.190827000 +0100
++++ a/source/utils/owrt_smbpasswd.c	2017-10-03 16:07:54.862857000 +0100
+@@ -108,7 +108,7 @@
+ 		}
+ 	}
+ 
+-	fprintf(fp, line);
++	fprintf(fp, "%s", line);
+ 
+ out:
+ 	if(fp)
+@@ -134,20 +134,20 @@
+ 			p = strchr(t, ':');
+ 			if(p && (p - t == strlen(user)) && (strncmp(t, user, strlen(user))) == 0)
+ 			{
+-				fpos_t r_pos, w_pos;
++				long int r_pos, w_pos;
+ 				char t2[256];
+-				fgetpos(fp, &r_pos);
++				r_pos = ftell(fp);
+ 				w_pos = r_pos;
+-				w_pos.__pos -= strlen(t);
++				w_pos -= strlen(t);
+ 				while(fgets(t2, 256, fp))
+ 				{
+-					fsetpos(fp, &w_pos);
++					fseek(fp, w_pos, SEEK_SET);
+ 					fputs(t2, fp);
+-					r_pos.__pos += strlen(t2);
+-					w_pos.__pos += strlen(t2);
+-					fsetpos(fp, &r_pos);
++					r_pos += strlen(t2);
++					w_pos += strlen(t2);
++					fseek(fp, r_pos, SEEK_SET);
+ 				}
+-				ftruncate(fileno(fp), w_pos.__pos);
++				ftruncate(fileno(fp), w_pos);
+ 				break;
+ 			}
+ 		}

tptest/Makefile

@@ -6,7 +6,7 @@ PKG_RELEASE:=0
 
 PKG_SOURCE_VERSION:=57786908e7a0c790f303417b459c562887582384
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_URL:=http://public.inteno.se:/tptest
+PKG_SOURCE_URL:=https://dev.iopsys.eu/fork/tptest.git
 
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_RELEASE)-$(PKG_SOURCE_VERSION).tar.gz
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)

tptest/files/etc/config/speedtest

@@ -1,8 +1,5 @@
+
 config testserver '1'
-	option server 'tptest.bredband.net'
-	option port '1640'
-
-config testserver '2'
 	option server 'referens.sth.ip-performance.se'
-	option port '1642'
+	option port '1641'
 

tr064/.cproject

@@ -0,0 +1,107 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<?fileVersion 4.0.0?><cproject storage_type_id="org.eclipse.cdt.core.XmlProjectDescriptionStorage">
+	<storageModule moduleId="org.eclipse.cdt.core.settings">
+		<cconfiguration id="cdt.managedbuild.config.gnu.cross.exe.debug.1423203916">
+			<storageModule buildSystemId="org.eclipse.cdt.managedbuilder.core.configurationDataProvider" id="cdt.managedbuild.config.gnu.cross.exe.debug.1423203916" moduleId="org.eclipse.cdt.core.settings" name="Debug">
+				<externalSettings/>
+				<extensions>
+					<extension id="org.eclipse.cdt.core.ELF" point="org.eclipse.cdt.core.BinaryParser"/>
+					<extension id="org.eclipse.cdt.core.GASErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.GmakeErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.GLDErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.CWDLocator" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.GCCErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+				</extensions>
+			</storageModule>
+			<storageModule moduleId="cdtBuildSystem" version="4.0.0">
+				<configuration artifactName="${ProjName}" buildArtefactType="org.eclipse.cdt.build.core.buildArtefactType.exe" buildProperties="org.eclipse.cdt.build.core.buildArtefactType=org.eclipse.cdt.build.core.buildArtefactType.exe,org.eclipse.cdt.build.core.buildType=org.eclipse.cdt.build.core.buildType.debug" cleanCommand="rm -rf" description="" id="cdt.managedbuild.config.gnu.cross.exe.debug.1423203916" name="Debug" parent="cdt.managedbuild.config.gnu.cross.exe.debug">
+					<folderInfo id="cdt.managedbuild.config.gnu.cross.exe.debug.1423203916." name="/" resourcePath="">
+						<toolChain id="cdt.managedbuild.toolchain.gnu.cross.exe.debug.482080998" name="Cross GCC" superClass="cdt.managedbuild.toolchain.gnu.cross.exe.debug">
+							<targetPlatform archList="all" binaryParser="org.eclipse.cdt.core.ELF" id="cdt.managedbuild.targetPlatform.gnu.cross.1864775892" isAbstract="false" osList="all" superClass="cdt.managedbuild.targetPlatform.gnu.cross"/>
+							<builder buildPath="${workspace_loc:/tr064}/Debug" id="cdt.managedbuild.builder.gnu.cross.84968765" keepEnvironmentInBuildfile="false" managedBuildOn="true" name="Gnu Make Builder" superClass="cdt.managedbuild.builder.gnu.cross"/>
+							<tool id="cdt.managedbuild.tool.gnu.cross.c.compiler.912678595" name="Cross GCC Compiler" superClass="cdt.managedbuild.tool.gnu.cross.c.compiler">
+								<option defaultValue="gnu.c.optimization.level.none" id="gnu.c.compiler.option.optimization.level.732187738" name="Optimization Level" superClass="gnu.c.compiler.option.optimization.level" useByScannerDiscovery="false" valueType="enumerated"/>
+								<option id="gnu.c.compiler.option.debugging.level.406132207" name="Debug Level" superClass="gnu.c.compiler.option.debugging.level" useByScannerDiscovery="false" value="gnu.c.debugging.level.max" valueType="enumerated"/>
+								<inputType id="cdt.managedbuild.tool.gnu.c.compiler.input.656190220" superClass="cdt.managedbuild.tool.gnu.c.compiler.input"/>
+							</tool>
+							<tool id="cdt.managedbuild.tool.gnu.cross.cpp.compiler.894741631" name="Cross G++ Compiler" superClass="cdt.managedbuild.tool.gnu.cross.cpp.compiler">
+								<option id="gnu.cpp.compiler.option.optimization.level.1987025848" name="Optimization Level" superClass="gnu.cpp.compiler.option.optimization.level" useByScannerDiscovery="false" value="gnu.cpp.compiler.optimization.level.none" valueType="enumerated"/>
+								<option id="gnu.cpp.compiler.option.debugging.level.1506505331" name="Debug Level" superClass="gnu.cpp.compiler.option.debugging.level" useByScannerDiscovery="false" value="gnu.cpp.compiler.debugging.level.max" valueType="enumerated"/>
+							</tool>
+							<tool id="cdt.managedbuild.tool.gnu.cross.c.linker.1176314661" name="Cross GCC Linker" superClass="cdt.managedbuild.tool.gnu.cross.c.linker">
+								<inputType id="cdt.managedbuild.tool.gnu.c.linker.input.1134635640" superClass="cdt.managedbuild.tool.gnu.c.linker.input">
+									<additionalInput kind="additionalinputdependency" paths="$(USER_OBJS)"/>
+									<additionalInput kind="additionalinput" paths="$(LIBS)"/>
+								</inputType>
+							</tool>
+							<tool id="cdt.managedbuild.tool.gnu.cross.cpp.linker.1076025733" name="Cross G++ Linker" superClass="cdt.managedbuild.tool.gnu.cross.cpp.linker"/>
+							<tool id="cdt.managedbuild.tool.gnu.cross.archiver.862614592" name="Cross GCC Archiver" superClass="cdt.managedbuild.tool.gnu.cross.archiver"/>
+							<tool id="cdt.managedbuild.tool.gnu.cross.assembler.638528350" name="Cross GCC Assembler" superClass="cdt.managedbuild.tool.gnu.cross.assembler">
+								<inputType id="cdt.managedbuild.tool.gnu.assembler.input.390953300" superClass="cdt.managedbuild.tool.gnu.assembler.input"/>
+							</tool>
+						</toolChain>
+					</folderInfo>
+				</configuration>
+			</storageModule>
+			<storageModule moduleId="org.eclipse.cdt.core.externalSettings"/>
+		</cconfiguration>
+		<cconfiguration id="cdt.managedbuild.config.gnu.cross.exe.release.517635632">
+			<storageModule buildSystemId="org.eclipse.cdt.managedbuilder.core.configurationDataProvider" id="cdt.managedbuild.config.gnu.cross.exe.release.517635632" moduleId="org.eclipse.cdt.core.settings" name="Release">
+				<externalSettings/>
+				<extensions>
+					<extension id="org.eclipse.cdt.core.ELF" point="org.eclipse.cdt.core.BinaryParser"/>
+					<extension id="org.eclipse.cdt.core.GASErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.GmakeErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.GLDErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.CWDLocator" point="org.eclipse.cdt.core.ErrorParser"/>
+					<extension id="org.eclipse.cdt.core.GCCErrorParser" point="org.eclipse.cdt.core.ErrorParser"/>
+				</extensions>
+			</storageModule>
+			<storageModule moduleId="cdtBuildSystem" version="4.0.0">
+				<configuration artifactName="${ProjName}" buildArtefactType="org.eclipse.cdt.build.core.buildArtefactType.exe" buildProperties="org.eclipse.cdt.build.core.buildArtefactType=org.eclipse.cdt.build.core.buildArtefactType.exe,org.eclipse.cdt.build.core.buildType=org.eclipse.cdt.build.core.buildType.release" cleanCommand="rm -rf" description="" id="cdt.managedbuild.config.gnu.cross.exe.release.517635632" name="Release" parent="cdt.managedbuild.config.gnu.cross.exe.release">
+					<folderInfo id="cdt.managedbuild.config.gnu.cross.exe.release.517635632." name="/" resourcePath="">
+						<toolChain id="cdt.managedbuild.toolchain.gnu.cross.exe.release.2086871607" name="Cross GCC" superClass="cdt.managedbuild.toolchain.gnu.cross.exe.release">
+							<targetPlatform archList="all" binaryParser="org.eclipse.cdt.core.ELF" id="cdt.managedbuild.targetPlatform.gnu.cross.1691338213" isAbstract="false" osList="all" superClass="cdt.managedbuild.targetPlatform.gnu.cross"/>
+							<builder buildPath="${workspace_loc:/tr064}/Release" id="cdt.managedbuild.builder.gnu.cross.2045398730" keepEnvironmentInBuildfile="false" managedBuildOn="true" name="Gnu Make Builder" superClass="cdt.managedbuild.builder.gnu.cross"/>
+							<tool id="cdt.managedbuild.tool.gnu.cross.c.compiler.804948441" name="Cross GCC Compiler" superClass="cdt.managedbuild.tool.gnu.cross.c.compiler">
+								<option defaultValue="gnu.c.optimization.level.most" id="gnu.c.compiler.option.optimization.level.422910401" name="Optimization Level" superClass="gnu.c.compiler.option.optimization.level" useByScannerDiscovery="false" valueType="enumerated"/>
+								<option id="gnu.c.compiler.option.debugging.level.1240870180" name="Debug Level" superClass="gnu.c.compiler.option.debugging.level" useByScannerDiscovery="false" value="gnu.c.debugging.level.none" valueType="enumerated"/>
+								<inputType id="cdt.managedbuild.tool.gnu.c.compiler.input.118715116" superClass="cdt.managedbuild.tool.gnu.c.compiler.input"/>
+							</tool>
+							<tool id="cdt.managedbuild.tool.gnu.cross.cpp.compiler.119838407" name="Cross G++ Compiler" superClass="cdt.managedbuild.tool.gnu.cross.cpp.compiler">
+								<option id="gnu.cpp.compiler.option.optimization.level.198417757" name="Optimization Level" superClass="gnu.cpp.compiler.option.optimization.level" useByScannerDiscovery="false" value="gnu.cpp.compiler.optimization.level.most" valueType="enumerated"/>
+								<option id="gnu.cpp.compiler.option.debugging.level.380023243" name="Debug Level" superClass="gnu.cpp.compiler.option.debugging.level" useByScannerDiscovery="false" value="gnu.cpp.compiler.debugging.level.none" valueType="enumerated"/>
+							</tool>
+							<tool id="cdt.managedbuild.tool.gnu.cross.c.linker.751400281" name="Cross GCC Linker" superClass="cdt.managedbuild.tool.gnu.cross.c.linker">
+								<inputType id="cdt.managedbuild.tool.gnu.c.linker.input.398459196" superClass="cdt.managedbuild.tool.gnu.c.linker.input">
+									<additionalInput kind="additionalinputdependency" paths="$(USER_OBJS)"/>
+									<additionalInput kind="additionalinput" paths="$(LIBS)"/>
+								</inputType>
+							</tool>
+							<tool id="cdt.managedbuild.tool.gnu.cross.cpp.linker.1354328537" name="Cross G++ Linker" superClass="cdt.managedbuild.tool.gnu.cross.cpp.linker"/>
+							<tool id="cdt.managedbuild.tool.gnu.cross.archiver.1258554594" name="Cross GCC Archiver" superClass="cdt.managedbuild.tool.gnu.cross.archiver"/>
+							<tool id="cdt.managedbuild.tool.gnu.cross.assembler.2022763402" name="Cross GCC Assembler" superClass="cdt.managedbuild.tool.gnu.cross.assembler">
+								<inputType id="cdt.managedbuild.tool.gnu.assembler.input.1223740654" superClass="cdt.managedbuild.tool.gnu.assembler.input"/>
+							</tool>
+						</toolChain>
+					</folderInfo>
+				</configuration>
+			</storageModule>
+			<storageModule moduleId="org.eclipse.cdt.core.externalSettings"/>
+		</cconfiguration>
+	</storageModule>
+	<storageModule moduleId="cdtBuildSystem" version="4.0.0">
+		<project id="tr064.cdt.managedbuild.target.gnu.cross.exe.1457888368" name="Executable" projectType="cdt.managedbuild.target.gnu.cross.exe"/>
+	</storageModule>
+	<storageModule moduleId="scannerConfiguration">
+		<autodiscovery enabled="true" problemReportingEnabled="true" selectedProfileId=""/>
+		<scannerConfigBuildInfo instanceId="cdt.managedbuild.config.gnu.cross.exe.debug.1423203916;cdt.managedbuild.config.gnu.cross.exe.debug.1423203916.;cdt.managedbuild.tool.gnu.cross.c.compiler.912678595;cdt.managedbuild.tool.gnu.c.compiler.input.656190220">
+			<autodiscovery enabled="true" problemReportingEnabled="true" selectedProfileId=""/>
+		</scannerConfigBuildInfo>
+		<scannerConfigBuildInfo instanceId="cdt.managedbuild.config.gnu.cross.exe.release.517635632;cdt.managedbuild.config.gnu.cross.exe.release.517635632.;cdt.managedbuild.tool.gnu.cross.c.compiler.804948441;cdt.managedbuild.tool.gnu.c.compiler.input.118715116">
+			<autodiscovery enabled="true" problemReportingEnabled="true" selectedProfileId=""/>
+		</scannerConfigBuildInfo>
+	</storageModule>
+	<storageModule moduleId="org.eclipse.cdt.core.LanguageSettingsProviders"/>
+	<storageModule moduleId="org.eclipse.cdt.make.core.buildtargets"/>
+</cproject>

tr064/.project

@@ -0,0 +1,27 @@
+<?xml version="1.0" encoding="UTF-8"?>
+<projectDescription>
+	<name>tr064</name>
+	<comment></comment>
+	<projects>
+		<project>openssl-1.0.2i</project>
+	</projects>
+	<buildSpec>
+		<buildCommand>
+			<name>org.eclipse.cdt.managedbuilder.core.genmakebuilder</name>
+			<triggers>clean,full,incremental,</triggers>
+			<arguments>
+			</arguments>
+		</buildCommand>
+		<buildCommand>
+			<name>org.eclipse.cdt.managedbuilder.core.ScannerConfigBuilder</name>
+			<triggers>full,incremental,</triggers>
+			<arguments>
+			</arguments>
+		</buildCommand>
+	</buildSpec>
+	<natures>
+		<nature>org.eclipse.cdt.core.cnature</nature>
+		<nature>org.eclipse.cdt.managedbuilder.core.managedBuildNature</nature>
+		<nature>org.eclipse.cdt.managedbuilder.core.ScannerConfigNature</nature>
+	</natures>
+</projectDescription>

tr064/.settings/language.settings.xml

@@ -0,0 +1,25 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no"?>
+<project>
+	<configuration id="cdt.managedbuild.config.gnu.cross.exe.debug.1423203916" name="Debug">
+		<extension point="org.eclipse.cdt.core.LanguageSettingsProvider">
+			<provider copy-of="extension" id="org.eclipse.cdt.ui.UserLanguageSettingsProvider"/>
+			<provider-reference id="org.eclipse.cdt.core.ReferencedProjectsLanguageSettingsProvider" ref="shared-provider"/>
+			<provider-reference id="org.eclipse.cdt.managedbuilder.core.MBSLanguageSettingsProvider" ref="shared-provider"/>
+			<provider class="org.eclipse.cdt.internal.build.crossgcc.CrossGCCBuiltinSpecsDetector" console="false" env-hash="1404192411374960532" id="org.eclipse.cdt.build.crossgcc.CrossGCCBuiltinSpecsDetector" keep-relative-paths="false" name="CDT Cross GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
+				<language-scope id="org.eclipse.cdt.core.gcc"/>
+				<language-scope id="org.eclipse.cdt.core.g++"/>
+			</provider>
+		</extension>
+	</configuration>
+	<configuration id="cdt.managedbuild.config.gnu.cross.exe.release.517635632" name="Release">
+		<extension point="org.eclipse.cdt.core.LanguageSettingsProvider">
+			<provider copy-of="extension" id="org.eclipse.cdt.ui.UserLanguageSettingsProvider"/>
+			<provider-reference id="org.eclipse.cdt.core.ReferencedProjectsLanguageSettingsProvider" ref="shared-provider"/>
+			<provider-reference id="org.eclipse.cdt.managedbuilder.core.MBSLanguageSettingsProvider" ref="shared-provider"/>
+			<provider class="org.eclipse.cdt.internal.build.crossgcc.CrossGCCBuiltinSpecsDetector" console="false" env-hash="1404192411374960532" id="org.eclipse.cdt.build.crossgcc.CrossGCCBuiltinSpecsDetector" keep-relative-paths="false" name="CDT Cross GCC Built-in Compiler Settings" parameter="${COMMAND} ${FLAGS} -E -P -v -dD &quot;${INPUTS}&quot;" prefer-non-shared="true">
+				<language-scope id="org.eclipse.cdt.core.gcc"/>
+				<language-scope id="org.eclipse.cdt.core.g++"/>
+			</provider>
+		</extension>
+	</configuration>
+</project>

tr064/Makefile

@@ -0,0 +1,82 @@
+# Copyright (C) 2017 PIVA Software <www.pivasoftware.com>
+# 	Author: OMAR Kallel <omar.kallel@pivasoftware.com>
+
+include $(TOPDIR)/rules.mk
+
+PKG_NAME:=tr064
+PKG_VERSION:=1.0
+PKG_SOURCE_URL:=https://dev.iopsys.eu/suite/tr-064.git
+PKG_SOURCE_PROTO:=git
+PKG_SOURCE_VERSION:=e53d492a09c433718a520987c419cb6a4d4ae8dc
+PKG_RELEASE=$(PKG_SOURCE_VERSION)
+PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION).tar.gz
+PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
+
+PKG_CONFIG_DEPENDS:= \
+	CONFIG_TR064_DEBUG \
+	CONFIG_TR064_DEVEL
+
+PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)/$(PKG_NAME)-$(PKG_VERSION)
+
+include $(INCLUDE_DIR)/package.mk
+
+define Package/tr064
+  SECTION:=utils
+  CATEGORY:=Utilities
+  TITLE:=tr064
+  DEPENDS:=+libubus +libuci +libubox +libmicroxml +libjson-c +libpthread +libdatamodel +libopenssl +libubus +libubox
+endef
+
+define Package/tr064/description
+	TR-064 protocol
+endef
+
+TARGET_CFLAGS += \
+	-D_GNU_SOURCE
+
+TARGET_LDFLAGS += \
+	-Wl,-rpath-link=$(STAGING_DIR)/usr/lib
+
+CONFIGURE_ARGS += \
+	--with-uci-include-path=$(STAGING_DIR)/usr/include \
+	--with-libubox-include-path=$(STAGING_DIR)/usr/include \
+	--with-libubus-include-path=$(STAGING_DIR)/usr/include
+
+ifeq ($(CONFIG_TR064_DEBUG),y)
+CONFIGURE_ARGS += \
+	--enable-debug
+endif
+
+ifeq ($(CONFIG_TR064_DEVEL),y)
+CONFIGURE_ARGS += \
+	--enable-devel
+endif
+
+CONFIGURE_ARGS += \
+	--enable-jsonc=1
+
+define Package/tr064/conffiles
+/etc/config/tr064
+endef
+
+define Package/tr064/install
+	$(INSTALL_DIR) $(1)/usr/bin
+	$(INSTALL_DIR) $(1)/etc/config
+	$(INSTALL_DIR) $(1)/etc/upnp-md
+	$(INSTALL_DIR) $(1)/etc/upnp-md/web
+	$(INSTALL_DIR) $(1)/etc/upnp-md/x509
+	$(INSTALL_DIR) $(1)/etc/init.d
+	$(INSTALL_BIN) $(PKG_BUILD_DIR)/upnp-md-pupnp/upnp-md $(1)/usr/bin
+	$(CP) $(PKG_BUILD_DIR)/web/*.xml $(1)/etc/upnp-md/web
+	$(CP) $(PKG_BUILD_DIR)/tools/parse_ftp_server_log.sh $(1)/usr/bin
+	$(CP) $(PKG_BUILD_DIR)/tools/kill_child.sh $(1)/usr/bin
+	$(CP) $(PKG_BUILD_DIR)/x509/*.pem $(1)/etc/upnp-md/x509
+	$(INSTALL_CONF) $(PKG_BUILD_DIR)/conf/upnp-md.conf $(1)/etc/upnp-md
+	$(CP) $(PKG_BUILD_DIR)/conf/DMconf.xml $(1)/etc/upnp-md
+	$(CP) $(PKG_BUILD_DIR)/conf/CPID.csv $(1)/etc/upnp-md
+	$(CP) $(PKG_BUILD_DIR)/conf/tr064 $(1)/etc/config
+	$(CP) $(PKG_BUILD_DIR)/conf/tr064d $(1)/etc/init.d
+	chmod 0744 $(1)/etc/init.d/tr064d
+endef
+
+$(eval $(call BuildPackage,tr064))

uboot/Makefile

@@ -9,11 +9,10 @@ include $(TOPDIR)/rules.mk
 
 PKG_NAME:=u-boot
 PKG_VERSION:=2016.08
-PKG_RELEASE:=2
-PKG_SOURCE_URL:=http://public.inteno.se:/uboot
+PKG_RELEASE:=4
+PKG_SOURCE_URL:=https://dev.iopsys.eu/fork/uboot.git
 PKG_SOURCE_PROTO:=git
-PKG_SOURCE_VERSION:=fccb9d5ee720a9f60cba917ded83e5cebe221eef
-
+PKG_SOURCE_VERSION:=f502d1b589f14142bf7d7719e8434014f180d03f
 PKG_BUILD_DIR:=$(BUILD_DIR)/$(PKG_NAME)-$(BUILD_VARIANT)/$(PKG_NAME)-$(PKG_VERSION)
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz

ubus-mqtt/Makefile

@@ -11,7 +11,7 @@ PKG_NAME:=ubus-mqtt
 PKG_VERSION:=14.20.0
 PKG_RELEASE:=1
 
-PKG_SOURCE_URL:=http://public.inteno.se:/ubus-mqtt
+PKG_SOURCE_URL:=https://dev.iopsys.eu/3rdparty/ubus-mqtt.git
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_VERSION:=$(PKG_VERSION)
 PKG_SOURCE:=$(PKG_NAME)-$(PKG_VERSION)-$(PKG_SOURCE_VERSION).tar.gz

voice-client/Makefile

@@ -16,7 +16,7 @@ define Package/voice-client
   SECTION:=net
   CATEGORY:=Network
   TITLE:=voice-client
-  DEPENDS:=+asterisk18-mod
+#  DEPENDS:=@(asterisk13||asterisk18-mod)
 endef
 
 define Package/voice-client/description

voice-client/files/etc/asterisk_templates/brcm_line.TEMPLATE

@@ -4,7 +4,7 @@ callerid=|CALLERID|
 autodial=|AUTODIAL|
 autodial_timeoutmsec=|AUTODIAL_TIMEOUT|
 dialtone_timeoutmsec=|DIALTONE_TIMEOUT|
-;jitter_fixed=|JITTERFIXED|
+jitter_fixed=|JITTERFIXED|
 ;jitter_min=|JITTERMIN|
 ;jitter_max=|JITTERMAX|
 ;jitter_target=|JITTERTARGET|

voice-client/files/etc/asterisk_templates/extensions_macro.conf.TEMPLATE

@@ -96,7 +96,7 @@ exten => s,n,			Hangup()
 
 ;handle busy (with CBBS support)
 exten => s-BUSY,1,		Read(DIGIT,Busy,1,in,30)
-exten => s-BUSY,n,		GotoIf($[${DIGIT} = ${ARG8}]?ccbs)
+exten => s-BUSY,n,		GotoIf($["${DIGIT}" = "${ARG8}"]?ccbs)
 exten => s-BUSY,n,		Hangup()
 exten => s-BUSY,n(ccbs),	Set(result=${SHELL(/usr/lib/asterisk/cbbs.sh ${ARG1} ${ARG2} ${ARG3} ${ARG4} ${ARG5} ${ARG6} ${ARG7})})
 exten => s-BUSY,n,		Playback(beep)

voice-client/files/etc/asterisk_templates/sip_registration_voicesec.TEMPLATE

@@ -1,2 +1,2 @@
-#exec echo "register => |TRANSPORT|://|USER|@|DOMAIN|:$(/usr/bin/voicesec -d /usr/lib/asterisk/voicesec_|PROVIDER|)|AUTHUSER|@|PROVIDER||PORT|/|CONTACT_USER|"
+#exec echo 'register => |TRANSPORT|://|USER|@|DOMAIN|:'$(/usr/bin/voicesec -d /usr/lib/asterisk/voicesec_|PROVIDER|)'|AUTHUSER|@|PROVIDER||PORT|/|CONTACT_USER|'
 

voice-client/files/etc/config/voice_client

@@ -8,6 +8,7 @@ config 'brcm_line' 'brcm0'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm1'
 	option 'extension' '1111'
@@ -19,6 +20,7 @@ config 'brcm_line' 'brcm1'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm2'
 	option 'extension' '2222'
@@ -30,6 +32,7 @@ config 'brcm_line' 'brcm2'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm3'
 	option 'extension' '3333'
@@ -41,6 +44,7 @@ config 'brcm_line' 'brcm3'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm4'
 	option 'extension' '4444'
@@ -52,6 +56,7 @@ config 'brcm_line' 'brcm4'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm5'
 	option 'extension' '5555'
@@ -63,6 +68,7 @@ config 'brcm_line' 'brcm5'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm6'
 	option 'extension' '6666'
@@ -74,6 +80,7 @@ config 'brcm_line' 'brcm6'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'brcm_line' 'brcm7'
 	option 'extension' '7777'
@@ -85,6 +92,7 @@ config 'brcm_line' 'brcm7'
 	option 'echo_cancel' 1
 	option 'callwaiting' '0'
 	option 'clir' '0'
+	option 'jitter_fixed' '50'
 
 config 'dialplan' 'custom_dialplan'
 	option 'custom_outgoing_enabled' '0'
@@ -162,8 +170,15 @@ config 'sip_service_provider' 'sip0'
 	option 'cfim_off' '#21#'
 	option 'cfbs_on' '*61*'
 	option 'cfbs_off' '#61#'
+	option cw_on '*43#' 
+	option cw_off '#43#' 
+	option cw_status '*#43#'
 	option 'call_return' '*69'
 	option 'redial' '*66'
+	option cbbs_key '5' 
+	option cbbs_maxretry '5'
+	option cbbs_retrytime '20'
+	option cbbs_waittime '30'
 	option 'is_fax' '0'
 	option 'transport' 'udp'
 

voice-client/files/etc/init.d/voice_client

@@ -68,6 +68,7 @@ TMPL_ASTERISK=$TEMPLATEDIR/asterisk.conf.TEMPLATE
 TMPL_CDR=$TEMPLATEDIR/cdr.conf.TEMPLATE
 TMPL_CDR_SYSLOG=$TEMPLATEDIR/cdr_syslog.conf.TEMPLATE
 TMPL_INDICATIONS=$TEMPLATEDIR/indications.conf.TEMPLATE
+TMPL_CEL=$TEMPLATEDIR/cel.conf.TEMPLATE
 TMPL_LOGGER=$TEMPLATEDIR/logger.conf.TEMPLATE
 TMPL_MANAGER=$TEMPLATEDIR/manager.conf.TEMPLATE
 TMPL_MODULES=$TEMPLATEDIR/modules.conf.TEMPLATE
@@ -80,7 +81,7 @@ TMPL_BRCM_LINE=$TEMPLATEDIR/brcm_line.TEMPLATE
 
 TMPL_MEETME=$TEMPLATEDIR/meetme.conf.TEMPLATE
 
-SPECRATEDIR=$ASTERISKDIR/special_rate_nr.cfg
+SPECRATECFG=$ASTERISKDIR/special_rate_nr.cfg
 
 run_hook()
 {
@@ -97,13 +98,13 @@ escape_sed_substitution()
 # Gets rid of any config files from $ASTERISKDIR not found in $WORKDIR.
 clean_up_asterisk_config_dir()
 {
-        for f in $ASTERISKDIR/* ; do
-                basef="`basename $f`"
-                if [ ! -e "$WORKDIR/$basef" ] ; then
-                        rm -rf "$f"
+	for f in $ASTERISKDIR/* ; do
+		basef="`basename $f`"
+		if [ ! -e "$WORKDIR/$basef" ] ; then
+			rm -rf "$f"
 			echo "$f" >> /tmp/voice.log
-                fi
-        done
+		fi
+	done
 }
 
 # Compares md5sums of the config files in $WORKDIR to those
@@ -113,7 +114,7 @@ compare_configs_and_copy_changed()
 {
 	# First, compute md5sums of the config files in $WORKDIR.
 	cd $WORKDIR/
-	md5sum * > $MD5SUMSFILE
+	md5sum * > $MD5SUMSFILE 2>/dev/null
 
 	# Now, check the files in $ASTERISKDIR against the md5sums.
 	cd $ASTERISKDIR/
@@ -141,15 +142,15 @@ assemble_and_copy_config()
 	# start if a config item is missing and an included config file isn't created.
 
 	# Copy the template files which we don't edit.
-	cp $TMPL_ASTERISK		$WORKDIR/asterisk.conf
-	cp $TMPL_CDR			$WORKDIR/cdr.conf
-	cp $TMPL_CEL			$WORKDIR/cel.conf
-	cp $TMPL_INDICATIONS		$WORKDIR/indications.conf
-	cp $TMPL_MANAGER		$WORKDIR/manager.conf
-	cp $TMPL_MODULES		$WORKDIR/modules.conf
-	cp $TMPL_EXTENSIONS_MACRO	$WORKDIR/extensions_macro.conf
-	cp $TMPL_MUSICONHOLD		$WORKDIR/musiconhold.conf
-	cp $SPECRATEDIR                 $WORKDIR/special_rate_nr.cfg
+	[ -f $TMPL_ASTERISK ]		&& cp $TMPL_ASTERISK		$WORKDIR/asterisk.conf
+	[ -f $TMPL_CDR ]		&& cp $TMPL_CDR			$WORKDIR/cdr.conf
+	[ -f $TMPL_CEL ]		&& cp $TMPL_CEL			$WORKDIR/cel.conf
+	[ -f $TMPL_INDICATIONS ]	&& cp $TMPL_INDICATIONS		$WORKDIR/indications.conf
+	[ -f $TMPL_MANAGER ]		&& cp $TMPL_MANAGER		$WORKDIR/manager.conf
+	[ -f $TMPL_MODULES ]		&& cp $TMPL_MODULES		$WORKDIR/modules.conf
+	[ -f $TMPL_EXTENSIONS_MACRO ]	&& cp $TMPL_EXTENSIONS_MACRO	$WORKDIR/extensions_macro.conf
+	[ -f $TMPL_MUSICONHOLD ]	&& cp $TMPL_MUSICONHOLD		$WORKDIR/musiconhold.conf
+	[ -f $SPECRATECFG ]		&& cp $SPECRATECFG		$WORKDIR/special_rate_nr.cfg
 	
 	test -e $TMPL_MEETME && cp $TMPL_MEETME $WORKDIR/meetme.conf
 	
@@ -178,7 +179,7 @@ assemble_and_copy_config()
 	mv $WORKDIR/features.tmp		$WORKDIR/features.conf
 	mv $WORKDIR/voicemail.tmp		$WORKDIR/voicemail.conf
 	mv $WORKDIR/meetme.tmp			$WORKDIR/meetme.conf
-        mv $WORKDIR/logger.tmp			$WORKDIR/logger.conf
+	mv $WORKDIR/logger.tmp			$WORKDIR/logger.conf
 	mv $WORKDIR/queues.tmp			$WORKDIR/queues.conf
 	mv $WORKDIR/dnsmgr.tmp			$WORKDIR/dnsmgr.conf
 
@@ -467,13 +468,13 @@ configure_sip()
 	if [ -z "$registertimeoutbackoff" ] ; then
 		sed -i "s/registertimeoutbackoff=|REGISTERTIMEOUTBACKOFF|/;registertimeoutbackoff=/g"    $WORKDIR/sip.tmp
 	else
-		sed -i "s/|REGISTERTIMEOUTBACKOFF|/$registertimeoutbackoff/g"                             $WORKDIR/sip.tmp
+		sed -i "s/|REGISTERTIMEOUTBACKOFF|/$registertimeoutbackoff/g"			     $WORKDIR/sip.tmp
 	fi
 
 	if [ -z "$registerattemptsbackoff" ] ; then
 		sed -i "s/registerattemptsbackoff=|REGISTERATTEMPTSBACKOFF|/;registerattemptsbackoff=/g"  $WORKDIR/sip.tmp
 	else
-		sed -i "s/|REGISTERATTEMPTSBACKOFF|/$registerattemptsbackoff/g"                           $WORKDIR/sip.tmp
+		sed -i "s/|REGISTERATTEMPTSBACKOFF|/$registerattemptsbackoff/g"			   $WORKDIR/sip.tmp
 	fi
 
 	if [ -z "$register403timeout" ] ; then
@@ -542,7 +543,7 @@ configure_sip()
 	for section in ${CONFIG_SECTIONS}; do
 		local transport
 		config_get cfgtype "$section" TYPE
-	        [ -n "$type" -a "x$cfgtype" != "x$type" ] && continue
+		[ -n "$type" -a "x$cfgtype" != "x$type" ] && continue
 		config_get transport $section transport
 		if [ "$transport" == "tls" ] ; then
 			tlsenable="yes"
@@ -720,6 +721,10 @@ configure_sip_provider()
 	config_get transport $1 transport
 	config_get encryption $1 encryption
 
+	# This is a hack to fix security issue #14962
+	user=${user//"'"/}
+	authuser=${authuser//"'"/}
+
 	if [ -z "$transport" ] ; then 
 		transport="udp" 
 	fi
@@ -804,7 +809,7 @@ configure_sip_provider()
 	fi
 	sed -i "s/|AUTOFRAMING|/$autoframing/"			$WORKDIR/sip_provider.tmp
 
-	# Set registered extension so that incoming calls match the correct peer                     
+	# Set registered extension so that incoming calls match the correct peer
 	sed -i "s/|CONTACT_USER|/$user/g"      $WORKDIR/sip_provider.tmp
 
 	# Add SIP Provider configuration to the temp file containing all SIP Provider configs.
@@ -1035,7 +1040,7 @@ configure_queue()
 	echo "[macro-$1]" >>					$WORKDIR/macros.tmp
 	echo "exten => s,1,Answer()" >>				$WORKDIR/macros.tmp
 
-        # Workaround to fix no ringback issue for incoming SIP calls
+	# Workaround to fix no ringback issue for incoming SIP calls
 	echo "exten => s,n,Playback(silence/1)" >>		$WORKDIR/macros.tmp
 
 	echo "exten => s,n,Queue($1,R)" >>			$WORKDIR/macros.tmp
@@ -1127,13 +1132,13 @@ configure_cdr()
 
 	echo "cdr_syslog: $cdr_syslog"
 
-        if [ -z "$cdr_syslog" ] ; then
+	if [ -z "$cdr_syslog" ] ; then
 	    cdr_syslog='0'
 	fi
 
 	# Enable/disable CDR logging in syslog
 	if [ "$cdr_syslog" == "1" ] ; then
-            cp $TMPL_CDR_SYSLOG		        $WORKDIR/cdr_syslog.conf
+	    cp $TMPL_CDR_SYSLOG			$WORKDIR/cdr_syslog.conf
 	fi
 }
 
@@ -1188,27 +1193,28 @@ configure_call_filters()
 	echo "exten => s,n(not-foreign),Set(FOREIGN=0)" >>	$WORKDIR/macros.tmp
 	echo "" >>						$WORKDIR/macros.tmp
 
-
 	# Get special rate numbers from /etc/asterisk/special_rate_nr.cfg
-	while read line
-	do
-	    i=0
-	    for v in $(echo $line | tr ";" "\n")
+	if [ -f $SPECRATECFG ]; then
+		while read line
 		do
-			if [ "$i" -eq "0" -a "$v" != "$country" ] ; then
-				continue 2
-			fi
-			if [ "$i" -eq "1" ] ; then
-				srn=$v
-			fi
-			i=$((i+1))
-		done
+		    i=0
+		    for v in $(echo $line | tr ";" "\n")
+			do
+				if [ "$i" -eq "0" -a "$v" != "$country" ] ; then
+					continue 2
+				fi
+				if [ "$i" -eq "1" ] ; then
+					srn=$v
+				fi
+				i=$((i+1))
+			done
 
-		if [ -n "$srn"  ] ; then
-			# Special rate numbers found
-			break
-		fi
-	done < "/etc/asterisk/special_rate_nr.cfg"
+			if [ -n "$srn"  ] ; then
+				# Special rate numbers found
+				break
+			fi
+		done < $SPECRATECFG
+	fi
 
 	echo "Found special rate numbers: $srn"
 
@@ -1327,8 +1333,8 @@ get_call_filter()
 	macro="NoOp()"
 	
 	if ! [ "x$direction" != "xincoming" -o "x$direction" != "xoutgoing" ] ; then
-                echo $macro
-        fi
+		echo $macro
+	fi
 
 	local call_filter enabled
 	config_get call_filter $provider call_filter "call_filter0"
@@ -1353,20 +1359,20 @@ configure_opening_hours_profile()
 	local section cfgtype
 	[ -z "$CONFIG_SECTIONS" ] && return 0
 	for section in ${CONFIG_SECTIONS}; do
-	        config_get cfgtype "$section" TYPE
-	        [ -n "timespan" -a "x$cfgtype" != "xtimespan" ] && continue
-	        local owner
+		config_get cfgtype "$section" TYPE
+		[ -n "timespan" -a "x$cfgtype" != "xtimespan" ] && continue
+		local owner
 	
-	        config_get owner $section owner
-	        if [ "$owner" == "$1" ] ; then
-	                local tr dow dom months
-	                config_get tr $section time_range
-	                config_get dow $section days_of_week
-	                config_get dom $section days_of_month
-	                config_get months $section months
+		config_get owner $section owner
+		if [ "$owner" == "$1" ] ; then
+			local tr dow dom months
+			config_get tr $section time_range
+			config_get dow $section days_of_week
+			config_get dom $section days_of_month
+			config_get months $section months
 	
-	                echo "exten => s,n,GotoIfTime($tr,$dow,$dom,$months,?$label)" >> $WORKDIR/macros.tmp
-	        fi
+			echo "exten => s,n,GotoIfTime($tr,$dow,$dom,$months,?$label)" >> $WORKDIR/macros.tmp
+		fi
 	done
 	if [ "$invert" == "0" ] ; then
 		echo "exten => s,n,Goto(closed)" >>		$WORKDIR/macros.tmp
@@ -1438,7 +1444,7 @@ configure_extensions()
 	
 	if [ -n "$record_message_extension" ] ; then
 		echo "exten => $record_message_extension,1,Playback(beep)"		>> $WORKDIR/extensions_local.tmp
-		echo "exten => $record_message_extension,n,Record(\"/usr/lib/asterisk/recordings/user-recording\${STRFTIME(\${EPOCH},,%C%y%m%d-%T)}.gsm)"	>> $WORKDIR/extensions_local.tmp
+		echo "exten => $record_message_extension,n,Record(\"/usr/lib/asterisk/recordings/user-recording\${STRFTIME(\${EPOCH},,%C%y%m%d-%T)}.gsm\")"	>> $WORKDIR/extensions_local.tmp
 		echo "exten => $record_message_extension,n,Playback(auth-thankyou)"	>> $WORKDIR/extensions_local.tmp
 		echo "exten => $record_message_extension,n,Hangup()"			>> $WORKDIR/extensions_local.tmp
 	fi
@@ -1641,7 +1647,7 @@ configure_extensions_provider()
 	local call_ivr call_queue extension
 	echo "exten => $user,n,Set(__TRANSFER_CONTEXT=\${CHANNEL(peername)}-transfer)" >>	$tmp
 
-        # replace prefix '+' with '00'
+	# replace prefix '+' with '00'
 	echo "exten => $user,n,GotoIf($[\"\${CALLERID(NUM):0:1}\" = \"+\"]?rewrite:norewrite)" >>	$tmp
 	echo "exten => $user,n(rewrite),Set(CALLERID(num)=\"00\${CALLERID(num):1}\"))" >>		$tmp
 	echo "exten => $user,n(norewrite),NoOp()">>							$tmp
@@ -1651,11 +1657,15 @@ configure_extensions_provider()
 	config_get call_queue $1 call_queue
 	config_get call_ivr $1 call_ivr
 	if [ -n "$incoming_lines" ]; then
-		echo "exten => $user,n,Dial($incoming_lines,$(get_voicemail_timeout),tF(hangup,h,2))" >>		$tmp
-		echo "exten => $user,n,GotoIf($[\"\${DIALSTATUS}\"=\"ANSWER\"]?endcall)" >>		$tmp
-		echo "exten => $user,n,GotoIf($[\"\${DIALSTATUS}\"=\"BUSY\"]?noanswer)" >>		$tmp
-		echo "exten => $user,n,GotoIf($[\"\${DIALSTATUS}\"=\"NOANSWER\"]?noanswer:endcall)" >>	$tmp
-		echo "exten => $user,n(noanswer),Macro(callhandler-noanswer,\${CHANNEL(peername)})" >>	$tmp
+	        echo "exten => $user,n,GotoIf(\${DB_EXISTS(CFBS/$1)}?cfbs)"         >> $tmp
+		echo "exten => $user,n,Dial($incoming_lines,$(get_voicemail_timeout),tF(hangup,h,2))"  >> $tmp
+		echo "exten => $user,n,Goto($user,nocfbs)"                                             >> $tmp
+		echo "exten => $user,n(cfbs),Dial($incoming_lines,20,tF(hangup,h,2))"                  >> $tmp
+		echo "exten => $user,n(nocfbs),NoOp()"                                                 >> $tmp
+		echo "exten => $user,n,GotoIf($[\"\${DIALSTATUS}\"=\"ANSWER\"]?endcall)"               >> $tmp
+		echo "exten => $user,n,GotoIf($[\"\${DIALSTATUS}\"=\"BUSY\"]?noanswer)"                >> $tmp
+		echo "exten => $user,n,GotoIf($[\"\${DIALSTATUS}\"=\"NOANSWER\"]?noanswer:endcall)"    >> $tmp
+		echo "exten => $user,n(noanswer),Macro(callhandler-noanswer,\${CHANNEL(peername)})"    >> $tmp
 		
 		# check for mailbox
 		config_get mailbox $1 mailbox
@@ -1704,7 +1714,7 @@ configure_brcm_line_extension()
 		echo "Configuring local extension $extension"
 
 		config_get cbbs_enabled "features" cbbs_enabled
-		# load cbbs settings if enabled                                                                                                                                             
+		# load cbbs settings if enabled
 		cbbs_key=""
 		cbbs_maxretry="0"
 		cbbs_retrytime="0"
@@ -1721,7 +1731,7 @@ configure_brcm_line_extension()
 		sed -i "s/|LINE|/$line/g"			$WORKDIR/extensions_local_line.tmp
 		sed -i "s/|TIMEOUT|/$(get_voicemail_timeout)/g"	$WORKDIR/extensions_local_line.tmp
 
-		#cbbs settings                                                                                                                                                              
+		#cbbs settings
 		sed -i "s/|CBBS_KEY|/$(escape_sed_substitution $cbbs_key)/"	$WORKDIR/extensions_local_line.tmp
 		sed -i "s/|MAX_RETRIES|/$cbbs_maxretry/"      			$WORKDIR/extensions_local_line.tmp
 		sed -i "s/|RETRYTIME|/$cbbs_retrytime/"				$WORKDIR/extensions_local_line.tmp
@@ -1998,8 +2008,8 @@ configure_conference()
 	echo "exten => $extension,n(enterno),Read(confno,,5)"			>> $WORKDIR/extensions_local.tmp
 	
 	for section in ${CONFIG_SECTIONS}; do
-                config_get cfgtype "$section" TYPE
-                [ "x$cfgtype" != "xconference_room" ] && continue
+		config_get cfgtype "$section" TYPE
+		[ "x$cfgtype" != "xconference_room" ] && continue
 
 		local name id enabled
 		config_get name $section name
@@ -2011,7 +2021,7 @@ configure_conference()
 		echo "Enabling conference room $id"
 		echo "exten => $extension,n,GotoIf($[\"\${confno}\"=\"$id\"]?enterconf)"	>> $WORKDIR/extensions_local.tmp
 		echo "conf => $id"								>> $WORKDIR/meetme.tmp
-        done
+	done
 
 	echo "exten => $extension,n,Playback(conf-invalid)"			>> $WORKDIR/extensions_local.tmp
 	echo "exten => $extension,n,Goto(enterno)"				>> $WORKDIR/extensions_local.tmp
@@ -2281,11 +2291,13 @@ reload_service() {
 	# if there is a registered account
 	ubus call led.voice1 set '{"state":"off"}'
 
+	asterisk -rx "config reload $ASTERISKDIR/sip.conf"
+	sleep 1
 	asterisk -rx "core reload"
 	asterisk -rx "dialplan reload"
 	asterisk -rx "brcm reload"
 }
 
 service_triggers() {
-        procd_add_reload_trigger voice_client
+	procd_add_reload_trigger voice_client
 }

voice-client/files/etc/uci-defaults/99-voice_client

@@ -9,7 +9,6 @@ uci -q batch <<-EOT
 	set voice_client.call_filter0.block_special_rate=0
 	set voice_client.call_filter0.block_outgoing=0
 	set voice_client.call_filter0.block_incoming=0
-	commit voice_client
 EOT
 
 }
@@ -22,7 +21,6 @@ uci -q batch <<-EOT
 	set voice_client.RINGING_STATUS.status=0
 	set voice_client.RINGING_STATUS.enabled=0
 	set voice_client.RINGING_STATUS.shouldring=1
-	commit voice_client
 EOT
 
 }
@@ -35,5 +33,39 @@ uci -q batch <<-EOT
         commit firewall
 EOT
 
+
+# Workaround for devices with optional external Dect. For
+# boards where the Dect HW has been left out in factory,
+# we need to delete the brcm channels in UCI to prevent
+# them from showing up in the phone GUI.
+ulBoardStuffOption=$(tr -d "\x20\x0a" </proc/nvram/ulBoardStuffOption | tr -s "\x30")
+if test "$ulBoardStuffOption" = "0" -a -x "/usr/sbin/dectmngr2"; then
+	/etc/init.d/dect disable
+
+	db -q batch <<-EOT
+		set hw.board.hasDect=0
+		commit hw.board
+	EOT
+
+	uci -q batch <<-EOT
+		delete voice_client.brcm0
+		delete voice_client.brcm1
+		delete voice_client.brcm2
+		delete voice_client.brcm3
+	EOT
+fi
+
+
+# Add a small jitter buffer in Broadcom DSP for all voice
+# lines to compensate for chopping audio in some boards.
+for brcm in $(db get hw.board.VoicePortOrder); do
+	uci -q get voice_client.${brcm}.jitter_fixed >/dev/null ||
+		uci -q add_list voice_client.${brcm}.jitter_fixed=50
+done
+
+
+# Common UCI commit at the end to save CPU resources.
+uci -q commit voice_client
+
 exit 0
 

voicesec/Makefile

@@ -11,7 +11,7 @@ include $(INCLUDE_DIR)/kernel.mk
 PKG_NAME:=voicesec
 PKG_VERSION:=1.0
 
-PKG_SOURCE_URL:=git@private.inteno.se:voicesec
+PKG_SOURCE_URL:=git@dev.iopsys.eu:iopsys/voicesec.git
 PKG_SOURCE_PROTO:=git
 PKG_SOURCE_VERSION:=661c0091e579e284712aeed892e921cc84a6f0bb
 PKG_SOURCE_SUBDIR:=$(PKG_NAME)-$(PKG_VERSION)